How to bend a four-point saddle in EMT

How to bend · Published November 8, 2026

Between the bends of each offset

8″

A 4 inch high saddle at 30° on a Greenlee 841A, 3/4 inch EMT: the height × the multiplier.

Bender values: Greenlee Use Guide, Site-Rite 840–844 hand benders, page 9; Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4.

Four-point saddle on a Greenlee 841A, 3/4″ EMT: mark 1 at 17″, mark 2 at 25″, mark 3 at 33″, mark 4 at 41″41″33″25″17″END1234END1234
Four-point saddle on a Greenlee 841A, 3/4″ EMT: mark 1 at 17″, mark 2 at 25″, mark 3 at 33″, mark 4 at 41″. Numbered in bending order.
Bendbook’s bender list, with a Klein 3/4″ EMT bender picked

Your own marks

Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.

A four-point saddle is two offsets in one stick. The first offset lifts the conduit over a wide obstacle, the stick runs level across the top, and the second offset brings it back down. Use it when a three-point saddle would be too narrow for a beam, a box or a bundle of other pipe. You mark four bends, and you set the width of the level run yourself.

The worked example

Here is a saddle 4 inches high in 3/4 inch EMT, bent on a Greenlee 841A. The obstacle is 8 inches wide and the bends are 30°. The near edge of the obstacle is 24 inches from the end of the stick.

Worked exampleFour-point saddle on a Greenlee 841A, 3/4″ EMT, numbers as printed in the maker’s guide
Obstacle height
4″
Obstacle width
8″
Bend angle
30°
Distance to the obstacle
24″
MarkFrom the endLine up withBendDirection
117″Arrow30°First bend
225″Arrow30°Roll the conduit 180°
333″Arrow30°Same way as bend 2
441″Arrow30°Roll the conduit 180°
Multiplier
2
Shrink per inch of saddle height
1/4″
Distance between the bends of each offset
8″
Shrink of each offset
1″
Gain
1/4″

Bender values: Greenlee Use Guide, Site-Rite 840–844 hand benders, page 9; Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4.

Calculate this bend in Bendbook. Pick your bender, type your measurements, and every mark is drawn on the stick for you.

Why the marks sit where they do

The first two marks are the first offset, which lifts the conduit. The third and fourth are the second offset, which puts it back down. The gap between the second and third marks is the level run across the top, the width of the obstacle.

You are working toward the obstacle, so the first offset has to reach full height at its near edge. An offset pulls the stick in by its shrink as it bends. That is why the second mark sits past the near edge by one offset's shrink, and not on it.

Each offset takes its own shrink, so the whole saddle shortens the stick by twice the shrink of each offset in the table. That matters when the run has to land on a fixed point past the saddle.

Steps

  1. Measure from the end of the stick to the near edge of the obstacle.
  2. Measure the height and the width of the obstacle.
  3. Work out the distance between the two bends of each offset: the height × the multiplier. At 30° on a Greenlee 841A the multiplier is 2.
  4. Work out the shrink of one offset: the height × the shrink per inch. At 30° on this bender it is 1/4″ for every inch of height.
  5. The second mark goes at the near edge distance plus that shrink, measured from the end.
  6. The first mark goes the distance between bends back toward the end from the second mark.
  7. The third mark goes the width of the obstacle past the second mark.
  8. The fourth mark goes the distance between bends past the third mark.
  9. Line the first mark up with the arrow and bend 30°.
  10. Roll the stick half a turn (180°).
  11. Line the second mark up with the arrow and bend 30°. The first offset is done.
  12. Leave the stick as it is. Line the third mark up with the arrow and bend 30°, the same way as the second bend.
  13. Roll the stick back half a turn (180°), so the last bend points the same way as the first.
  14. Line the fourth mark up with the arrow and bend 30°.
  15. Lay the stick on a flat floor. Both ends must lie flat in one plane. Hold it up to the obstacle before you fasten it.

Mistakes that cost a stick

  • Rolling at the wrong time. Roll between the first and second bends, leave the stick alone between the second and third, and roll it back before the fourth.
  • Putting the second mark on the near edge. Without the shrink, the whole saddle lands short by that shrink, and the second offset comes down onto the far side of the obstacle.
  • Dog legs. If the stick turns in the bender between bends, the two offsets no longer lie in one plane. Roll exactly 180° and keep the stick seated in the shoe.
  • Measuring from the wrong end. Every mark is measured from the same end of the stick. Pick one end and stay with it.
  • Forgetting shrink when you cut. The saddle takes the shrink of one offset twice. A saddle bent to the right height can still leave the stick short.
  • Over-bending. A bend past 30° makes the saddle taller and throws off the level run. Stop at 30° on the head and check the angle before you take the stick out.

The marks belong to the bender and conduit named in the example. Check the multiplier and shrink against your own bender before you cut a full stick.

Questions

When should I use a four-point saddle instead of a three-point saddle?

Use a four-point saddle when the obstacle is wide or square, such as a beam, a panel box or a bundle of pipes. A three-point saddle suits a narrow round pipe. The four-point style gives you a flat run across the top and lets you set the width yourself.

Can I use a different angle?

Yes. A shallower angle makes a longer, gentler saddle, and a steeper one makes it shorter. The multiplier and the shrink per inch both change with the angle. On this bender the printed multiplier at 45° is 1.4 and the shrink is 3/8″ per inch of height. Work out the marks again for the new angle.

Do the marks change with the bender?

They can. Multipliers and shrink are the maker's published values for one bender and one conduit size, so use the values for your own. If you bend rigid or IMC, use the values for that conduit, not the EMT ones.

Does the NEC limit how many bends I can put in a run?

Yes. The bends between pull points are limited in total, to 360°. The sections are 358.24 for EMT, 344.24 for rigid metal conduit and 342.24 for IMC. Every bend in a saddle counts toward that total, so add them to the rest of the run.

Check against your own bender. The numbers on this page use the values the maker publishes for the bender named; where the maker prints none, they are worked out from the geometry of the bend. Shoes wear, conduit varies and springback differs, so make one test bend and adjust before you bend the run.