Conduit bending guides
How to lay out and bend offsets, saddles, kicks and 90s with a hand bender, with worked examples, and the published values of the benders electricians use.

Your own marks
Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.
How to bend
- How to bend a three-point saddle in EMTBend a three-point saddle with a 45° center bend and two 22-1/2° outer bends, with the marks worked out for a Klein 56204 on 3/4 inch EMT.
- How to bend a four-point saddle in EMTMark and bend a four-point saddle to cross a beam, box or other wide obstacle, with a worked example, the bending order and the mistakes that cost a stick.
- How to bend a back-to-back 90 in EMTBend two 90s on one stick with a set distance between their backs: mark the first stub, then line the second mark up with the star.
- How to bend a kick in conduitA kick is a single bend that moves conduit off a wall. Here is how the depth sets the mark, and how to bend it with a hand bender.
- How to bend a 90 degree stub-up in EMT conduitSubtract the take-up, line the mark up with the arrow on the bender head, and bend to 90. A worked 1/2 inch EMT stub-up with steps and common mistakes.
- How to bend matching parallel offsets in conduitBend a rack of parallel offsets that stay evenly spaced: which way the marks shift from one conduit to the next, with a worked example and steps.
- 45 degree rolling offset: true offset and marksHow to bend a rolling offset at 45 degrees: work out the true offset from rise and roll, mark the stick, and make both bends without a dog leg.
- Conduit bender markings: the arrow, star and rim notchWhat the arrow, star, rim notch and degree lines on a hand bender head are for, and which bend lines up with which, with worked examples.
- How to bend an offset on 1 inch EMTBend an offset in 1 inch EMT with a hand bender: where the marks go, how to roll the conduit, and why the larger radius needs more room.
- How to bend a box offset on 3/4 inch EMTBend a box offset in 3/4 inch EMT so the conduit sits flat against the box. A worked example on a Klein 56204, with marks, steps and common mistakes.
- Three-point saddle formula: center mark, outer marks, shrinkThe 3-point saddle formula for hand benders: where the center mark goes, how far the outer marks sit from it, and how much shrink the saddle takes.
Bender charts
- Klein bender chart for EMT: take-up, multipliers and marksPublished take-up, stub marks, multipliers and offsets for Klein EMT hand benders by size, with a worked stub and offset on the Klein 56203.
- Greenlee conduit bender chart: take-up, multipliers and marksPublished values for Greenlee 840A, 841A, 842A and 843A EMT hand benders: take-up, multipliers, stub marks and offset marks, with worked examples.
- 1/2 EMT take-up: how to bend a 90 in 1/2 EMTThe take-up for 1/2 inch EMT hand benders, where to mark common stub heights, and a worked 90° stub-up showing how to pull it.
- 3/4 EMT take-up: how to bend a 90 in 3/4 EMTThe take-up for 3/4 inch EMT hand benders, where to mark common stub heights, and a worked 90° stub-up showing how to pull it.
- 1 inch EMT take-up and bending chartThe take-up for 1 inch EMT hand benders, where to mark common stub heights, and a worked 90° stub-up showing how to pull it.
- Greenlee 1800 mechanical bender chart for rigid conduitGreenlee 1800 chart for 3/4″ rigid and 1″ rigid: take-up, stub marks and radius, and why the mark goes on the hook, not an arrow.
- Gardner Bender conduit bender chart: take-up, multipliers and marksPublished values for the Gardner Bender 960, 961 and 962 EMT hand benders: take-up, stub marks, multipliers and offsets, with a worked stub and offset.
- 1-1/4 inch EMT take-up and bending chartThe take-up for 1-1/4 inch EMT hand benders, where to mark common stub heights, and a worked 90° stub-up showing how to pull it.
Reference
- Conduit bending multipliers: offset multiplier chartThe offset multiplier and shrink for each bend angle, as the maker prints them and as exact trigonometry gives them, and how to use them on a stick.
- Conduit bending chart and cheat sheet for hand bendersA one-page conduit bending chart: offset multipliers, shrink per inch and bender take-ups, with worked offsets and the mistakes that cost a stick.
- Conduit shrink chart: shrink per inch of offsetShrink per inch of offset depth by angle, the shrink for common depths, and when to add it to a mark and when to leave the marks alone.
- Hand bender take-up chart by maker, model and sizeTake-up (deduct) for Klein, Greenlee, Ideal and Gardner Bender hand benders by model and size, and how to check the take-up on your own bender.
- Offset multiplier for 22-1/2 degrees: printed and exactThe 22-1/2 degree offset multiplier and shrink per inch, printed and exact, with a worked 1/2 inch EMT example and the marks for a Klein 56203.
- The offset multiplier for 30 degreesThe 30 degree offset multiplier and shrink per inch, printed and exact, with a worked 1/2 inch EMT offset and the steps to bend it.
- 10 degree offset multiplier and how to use itThe printed multiplier for a 10 degree offset, with a worked example on a Klein 56203, the marks, the shrink, and when a shallow offset is worth bending.