Conduit bending chart and cheat sheet for hand benders
Reference · Published November 8, 2026
Offset multiplier at 30°
2
Multiply the offset depth by this to get the distance between bends. The tables below have every angle.
Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.

Your own marks
Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.
This is the conduit bending chart to keep open on the job: the multiplier and the shrink for each offset angle, and the take-up for each hand bender. Look up the figure for your angle and your bender, then check it against the guide that came with the bender before you cut a stick.
Offset multipliers
The multiplier turns the depth of an offset into the distance between its two bends. Multiply the depth by the multiplier for your angle. A shallow angle spreads the offset over a long run. A steep angle makes it short, but it is harder to pull wire through.
| Angle | Exact multiplier | Gardner Bender prints | Greenlee prints | Klein prints |
|---|---|---|---|---|
| 5° | 11.474 | — | — | — |
| 10° | 5.759 | 6 | 6 | 6 |
| 15° | 3.864 | — | 3.86 | — |
| 22-1/2° | 2.613 | 2.6 | 2.6 | 2.6 |
| 30° | 2 | 2 | 2 | 2 |
| 45° | 1.414 | 1.4 | 1.4 | 1.4 |
| 60° | 1.155 | 1.2 | 1.2 | 1.2 |
Use the printed columns. They are the figures in the makers' guides, the ones you check against the bender in your hand. The angles have their own pages: 10°, 22-1/2° and 30°, and every angle side by side.
Shrink per inch of offset
Every offset pulls the stick shorter. Multiply the depth by the shrink per inch for your angle to get the shrink for the whole offset. The steeper the angle, the more you lose.
| Angle | Exact shrink per inch | Gardner Bender prints | Greenlee prints | Klein prints |
|---|---|---|---|---|
| 5° | 1/16″ | — | — | — |
| 10° | 1/16″ | 1/16″ | 1/16″ | 1/16″ |
| 15° | 1/8″ | — | 1/8″ | — |
| 22-1/2° | 3/16″ | 3/16″ | 3/16″ | 3/16″ |
| 30° | 1/4″ | 1/4″ | 1/4″ | 1/4″ |
| 45° | 7/16″ | 3/8″ | 3/8″ | 3/8″ |
| 60° | 9/16″ | 1/2″ | 1/2″ | 1/2″ |
| Depth | 10° | 22-1/2° | 30° | 45° | 60° |
|---|---|---|---|---|---|
| 1″ | 1/16″ | 3/16″ | 1/4″ | 7/16″ | 9/16″ |
| 2″ | 3/16″ | 3/8″ | 9/16″ | 13/16″ | 1-1/8″ |
| 3″ | 1/4″ | 5/8″ | 13/16″ | 1-1/4″ | 1-3/4″ |
| 4″ | 3/8″ | 13/16″ | 1-1/16″ | 1-11/16″ | 2-5/16″ |
| 5″ | 7/16″ | 1″ | 1-5/16″ | 2-1/16″ | 2-7/8″ |
| 6″ | 1/2″ | 1-3/16″ | 1-5/8″ | 2-1/2″ | 3-7/16″ |
| 8″ | 11/16″ | 1-9/16″ | 2-1/8″ | 3-5/16″ | 4-5/8″ |
| 10″ | 7/8″ | 2″ | 2-11/16″ | 4-1/8″ | 5-3/4″ |
| 12″ | 1-1/16″ | 2-3/8″ | 3-3/16″ | 5″ | 6-15/16″ |
Which way you work decides whether shrink moves your marks:
- Working toward a fixed point, such as an obstacle or a box you are bending into, the marks must put the full depth at that point. The second worked offset below shows how.
- Working away from a fixed end, shrink does not move the marks. It only makes the run past the offset shorter, so it matters when you cut the stick.
The conduit shrink chart goes further.
Take-ups by bender
Take-up is the length a bender uses up in a 90°. For a stub, subtract the take-up from the stub height. That is your mark, measured from the end that will rise, and it goes on the arrow.
| Bender | Conduit | Take-up | Radius | Source |
|---|---|---|---|---|
| Gardner Bender 960 | 1/2″ EMT | 5″ | 3-11/16″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
| Gardner Bender 961 | 3/4″ EMT | 6″ | 4-3/4″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
| Gardner Bender 961 | 1/2″ rigid/IMC | 6″ | 4-3/4″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
| Gardner Bender 962 | 1″ EMT | 8″ | 5-13/16″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
| Gardner Bender 962 | 3/4″ rigid/IMC | 8″ | 5-13/16″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
| Greenlee 1800 | 1″ rigid/IMC | 11″ | 6-1/16″ | Greenlee 1800 Mechanical Bender instruction manual, page 6 |
| Greenlee 1800 | 3/4″ rigid/IMC | 8-1/2″ | 4-13/16″ | Greenlee 1800 Mechanical Bender instruction manual, page 6 |
| Greenlee 840A | 1/2″ EMT | 5″ | 4-3/16″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 840F | 1/2″ EMT | 5″ | 4-3/16″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 841A | 3/4″ EMT | 6″ | 5-1/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 841A | 1/2″ rigid/IMC | 6″ | 5-1/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 841F | 3/4″ EMT | 6″ | 5-1/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 841F | 1/2″ rigid/IMC | 6″ | 5-1/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 842A | 1″ EMT | 8″ | 6-1/2″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 842A | 3/4″ rigid/IMC | 8″ | 6-1/2″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 842F | 1″ EMT | 8″ | 6-1/2″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 842F | 3/4″ rigid/IMC | 8″ | 6-1/2″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843A | 1-1/4″ EMT | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843A | 1″ rigid/IMC | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843A | 1/2″ rigid/IMC | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843A | 3/4″ rigid/IMC | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843F | 1-1/4″ EMT | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843F | 1″ rigid/IMC | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843F | 1/2″ rigid/IMC | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843F | 3/4″ rigid/IMC | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 844A | 1/2″ EMT | 5″ | 4-3/16″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 844A | 3/4″ EMT | 6″ | 5-1/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 844A | 1/2″ rigid/IMC | 6″ | 5-1/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Ideal 74-001 | 1/2″ EMT | not published | — | — |
| Ideal 74-002 | 3/4″ EMT | 6″ | — | Ideal Conduit Bender Guide, page 3 |
| Ideal 74-002 | 1/2″ rigid/IMC | not published | — | — |
| Ideal 74-003 | 1″ EMT | not published | — | — |
| Ideal 74-003 | 3/4″ rigid/IMC | not published | — | — |
| Ideal 74-006 | 1-1/4″ EMT | not published | — | — |
| Ideal 74-006 | 1″ rigid/IMC | not published | — | — |
| Ideal 74-031 | 1/2″ EMT | not published | — | — |
| Ideal 74-032 | 3/4″ EMT | 6″ | — | Ideal Conduit Bender Guide, page 3 |
| Ideal 74-032 | 1/2″ rigid/IMC | not published | — | — |
| Ideal 74-033 | 1″ EMT | not published | — | — |
| Ideal 74-033 | 3/4″ rigid/IMC | not published | — | — |
| Ideal 74-036 | 1-1/4″ EMT | not published | — | — |
| Ideal 74-036 | 1″ rigid/IMC | not published | — | — |
| Klein 56203 | 1/2″ EMT | 5″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56204 | 3/4″ EMT | 6″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56204 | 1/2″ rigid/IMC | 6″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56205 | 1″ EMT | 8″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56205 | 3/4″ rigid/IMC | 8″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56206 | 1/2″ EMT | 5″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56207 | 3/4″ EMT | 6″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56207 | 1/2″ rigid/IMC | 6″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56211 | 1-1/4″ EMT | 11″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56211 | 1″ rigid/IMC | 11″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
Compare take-ups only between benders of the same conduit type and size. A 1/2 inch EMT bender and a 3/4 inch EMT bender differ for that reason alone.
Bender pages: Klein, Greenlee, Gardner Bender, Greenlee 1800 for rigid. By size: 1/2 inch EMT, 3/4 inch EMT, 1 inch EMT and 1-1/4 inch EMT. The full list is in the hand bender take-up chart.
A worked offset
A 6 inch offset at 30° in 1/2 inch EMT on a Klein 56203, measured from the end of the stick.
- Offset depth
- 6″
- Bend angle
- 30°
| Mark | From the end | Line up with | Bend | Direction |
|---|---|---|---|---|
| 1 | 12″ | Arrow | 30° | First bend |
| 2 | 24″ | Arrow | 30° | Roll the conduit 180° |
- Multiplier
- 2
- Shrink per inch of depth
- 1/4″
- Distance between bends
- 12″
- Shrink
- 1-1/2″
Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.
Calculate this bend in Bendbook. Pick your bender, type your measurements, and every mark is drawn on the stick for you.
Both marks go on the arrow. The first bend is the one nearest the end you measured from.
Working toward an obstacle
When the offset has to land at a fixed point, the marks move. Here is the same 6 inch offset at 30°, with the obstacle 30 inches from the end of the stick, measured to the far bend.
- Offset depth
- 6″
- Bend angle
- 30°
- Distance to the obstacle
- 30″
| Mark | From the end | Line up with | Bend | Direction |
|---|---|---|---|---|
| 1 | 31-1/2″ | Arrow | 30° | First bend |
| 2 | 19-1/2″ | Arrow | 30° | Roll the conduit 180° |
- Multiplier
- 2
- Shrink per inch of depth
- 1/4″
- Distance between bends
- 12″
- Shrink
- 1-1/2″
Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.
The far mark is the obstacle distance plus the shrink, 1/4″ for every inch of depth. That puts the full depth at the obstacle. The near mark is the distance between bends back toward the end. Bend the far mark first. The shrink is already in the marks, so do not add it again.
Steps
- Find the chart for your bender and conduit size. Do not use another bender's figures.
- Measure the offset depth.
- Multiply the depth by the multiplier for your angle. That is the distance between the marks.
- Working away from a fixed end, make the first mark where the offset should start, measured from that end. Make the second mark the distance between bends past it.
- Working toward an obstacle, add the shrink to the distance to the obstacle. That is the far mark. Make the near mark the distance between bends back toward the end.
- Line the mark you bend first up with the arrow and bend to the angle.
- Take the stick out and roll it exactly half a turn, 180°.
- Line the other mark up with the arrow and bend to the same angle.
- Lay the stick on a flat floor and check for twist.
- Working toward an obstacle, check that the full depth lands at it. Working away from a fixed end, measure the run past the offset before you cut.
Mistakes that cost a stick
- Dog legs. Rolling by less or more than half a turn between the two bends of an offset.
- Measuring from the wrong end. Pick the end and take both marks from it.
- Forgetting shrink toward an obstacle. The offset lands short, so the full depth is not at the obstacle.
- Over-bending. Watch the angle on the head and stop at it. Easing a bend back is guesswork.
- Using the wrong take-up. Take-up changes with bender, conduit type and size.
- Lining a mark up with a degree line. Degree lines show how far the bend has gone. Offset and stub marks go on the arrow.
Other bends
For stubs and 90s, see the 90 degree stub-up. For matching offsets, see parallel offsets. Other pages cover the rolling offset at 45°, the kick, the 3-point saddle, the 4-point saddle and the offset on 1 inch EMT. All guides are listed in the guides index.
Bends between pull points are limited by the NEC: see 358.24 for EMT and 344.24 for rigid metal conduit.
Questions
What is a conduit bending chart?
It lists the figures you need to mark a stick: multipliers, shrink per inch and the take-up of your bender. It saves you the arithmetic on the job.
Do I use the printed or the exact multiplier?
Use the printed one. It matches the maker's guide and the bender you are checking against. The exact column is the trigonometry, and at most angles it differs a little from the printed figure.
Does shrink change where I mark the conduit?
Only when you work toward a fixed point. Then the far mark goes past the obstacle distance by the shrink, as the obstacle example shows. Working away from a fixed end, shrink leaves the marks alone and shortens the run past the offset.
Can I use one bender's take-up on another?
Only if both are for the same conduit type and size and the table shows the same figure. Otherwise read the line for the bender and the size in your hand.
Check against your own bender. The numbers on this page use the values the maker publishes for the bender named; where the maker prints none, they are worked out from the geometry of the bend. Shoes wear, conduit varies and springback differs, so make one test bend and adjust before you bend the run.