Conduit shrink chart: shrink per inch of offset
Reference · Published November 8, 2026
Shrink per inch of depth at 30°
1/4″
Multiply the offset depth by this to get the shrink, as Klein prints it.
Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.

Your own marks
Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.
Shrink is how much shorter an offset makes the run. Every inch of offset depth costs a set length of stick, and that length depends on the bend angle. Multiply the depth by the shrink per inch for your angle to get the shrink for the whole offset. Whether it moves your marks depends on which way you are working.
Shrink per inch of depth, by angle
| Angle | Exact shrink per inch | Gardner Bender prints | Greenlee prints | Klein prints |
|---|---|---|---|---|
| 5° | 1/16″ | — | — | — |
| 10° | 1/16″ | 1/16″ | 1/16″ | 1/16″ |
| 15° | 1/8″ | — | 1/8″ | — |
| 22-1/2° | 3/16″ | 3/16″ | 3/16″ | 3/16″ |
| 30° | 1/4″ | 1/4″ | 1/4″ | 1/4″ |
| 45° | 7/16″ | 3/8″ | 3/8″ | 3/8″ |
| 60° | 9/16″ | 1/2″ | 1/2″ | 1/2″ |
| Depth | 10° | 22-1/2° | 30° | 45° | 60° |
|---|---|---|---|---|---|
| 1″ | 1/16″ | 3/16″ | 1/4″ | 7/16″ | 9/16″ |
| 2″ | 3/16″ | 3/8″ | 9/16″ | 13/16″ | 1-1/8″ |
| 3″ | 1/4″ | 5/8″ | 13/16″ | 1-1/4″ | 1-3/4″ |
| 4″ | 3/8″ | 13/16″ | 1-1/16″ | 1-11/16″ | 2-5/16″ |
| 5″ | 7/16″ | 1″ | 1-5/16″ | 2-1/16″ | 2-7/8″ |
| 6″ | 1/2″ | 1-3/16″ | 1-5/8″ | 2-1/2″ | 3-7/16″ |
| 8″ | 11/16″ | 1-9/16″ | 2-1/8″ | 3-5/16″ | 4-5/8″ |
| 10″ | 7/8″ | 2″ | 2-11/16″ | 4-1/8″ | 5-3/4″ |
| 12″ | 1-1/16″ | 2-3/8″ | 3-3/16″ | 5″ | 6-15/16″ |
The per-inch columns are the figures printed in each maker's guide. Those are the ones to check against the bender in your hand. If your bender's own guide disagrees with a chart, the guide wins.
The steeper the angle, the more the run shrinks. At 30° it is 1/4″ for every inch of depth, as Klein prints it.
The table by depth works the shrink out by exact geometry. At 45° and 60° that comes out a little more than the printed per-inch figure times the depth, because the printed figures are rounded. Use the printed figure when you work from your bender's guide, and use one or the other for a whole run, not both.
When shrink moves your marks
It depends on whether you work toward a fixed point or away from a fixed end.
Working toward a fixed point. This is an obstacle, or a box you are bending into. The marks have to put the full depth at that point, so the far mark goes past the obstacle distance by the shrink. The worked example below shows it.
Working away from a fixed end. Shrink does not move your marks. It only makes the run past the offset shorter. That matters when you cut the stick, so measure for the far end after you bend.
Worked example: bending to an obstacle
A 6 inch offset at 30° in 1/2 inch EMT on a Klein 56203 that has to land at an obstacle 30 inches from the end of the stick, measured to the far bend.
- Offset depth
- 6″
- Bend angle
- 30°
- Distance to the obstacle
- 30″
| Mark | From the end | Line up with | Bend | Direction |
|---|---|---|---|---|
| 1 | 31-1/2″ | Arrow | 30° | First bend |
| 2 | 19-1/2″ | Arrow | 30° | Roll the conduit 180° |
- Multiplier
- 2
- Shrink per inch of depth
- 1/4″
- Distance between bends
- 12″
- Shrink
- 1-1/2″
Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.
Calculate this bend in Bendbook. Pick your bender, type your measurements, and every mark is drawn on the stick for you.
The far mark sits past the obstacle distance by the shrink for the whole offset. That is what puts the full depth at the obstacle. The near mark is the distance between bends back toward the end. You bend the far mark first.
Steps
- Check the shrink per inch for your angle against your bender's guide.
- Measure from the end of the stick to the obstacle.
- Multiply the depth by the shrink per inch, 1/4″ at 30°. Add that to the distance to the obstacle. That is the far mark.
- Multiply the depth by the multiplier for your angle, 2 at 30°. Measure that back from the far mark, toward the end. That is the near mark.
- Line the far mark up with the arrow and bend to 30°.
- Take the stick out and roll it exactly half a turn, 180°.
- Line the near mark up with the arrow and bend to 30° again.
- Hold the stick up to the obstacle and check that the full depth lands there before you cut.
The marks are worked from one bender's printed figures. Check them against the guide for the bender in your hand.
Mistakes that cost a stick
- Adding shrink twice. When you work toward an obstacle, the far mark already carries it.
- Ignoring shrink when cutting. Working away from a fixed end, the run past the offset comes out short. Measure for the cut after you bend.
- Rolling the wrong amount. Anything but exactly 180° between bends gives a dog leg.
- Measuring from the wrong end. Both marks come from the same end. Mixing ends puts the offset in the wrong place.
- Mixing printed and exact figures. Pick one for the whole run.
Questions
Does shrink change with conduit size?
Makers print shrink per inch by angle, and the shrink of a plain offset follows from its depth and angle. The marks for other bends still differ by bender, so work from the guide for the bender you are using.
Do saddles shrink too?
Yes, a saddle pulls the stick shorter as well. See the three-point saddle and four-point saddle guides for how each one is marked.
Where do I find the multiplier for 30°?
The offset multiplier for 30 degrees guide covers it, and the conduit bending multipliers page has every angle.
Does a stub-up shrink the same way?
No. A stub-up is marked with take-up, not shrink. See the 90 degree stub-up guide.
Check against your own bender. The numbers on this page use the values the maker publishes for the bender named; where the maker prints none, they are worked out from the geometry of the bend. Shoes wear, conduit varies and springback differs, so make one test bend and adjust before you bend the run.