Conduit bending multipliers: offset multiplier chart
Reference · Published November 8, 2026
Offset multiplier at 45°
1.4
Multiply the offset depth by this to get the distance between bends, as Klein prints it.
Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.

Your own marks
Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.
An offset multiplier tells you how far apart to put your two marks. Multiply the depth of the offset by the multiplier for the angle you are bending, and that is the distance between the bends. Every angle has its own multiplier and its own shrink. The chart below lists the multipliers for the standard angles, as each maker prints them.
The multiplier chart
| Angle | Exact multiplier | Gardner Bender prints | Greenlee prints | Klein prints |
|---|---|---|---|---|
| 5° | 11.474 | — | — | — |
| 10° | 5.759 | 6 | 6 | 6 |
| 15° | 3.864 | — | 3.86 | — |
| 22-1/2° | 2.613 | 2.6 | 2.6 | 2.6 |
| 30° | 2 | 2 | 2 | 2 |
| 45° | 1.414 | 1.4 | 1.4 | 1.4 |
| 60° | 1.155 | 1.2 | 1.2 | 1.2 |
The smaller the angle, the longer the offset runs and the less length it costs. The bigger the angle, the shorter the run and the more shrink you have to allow for. Pick the angle the job gives you room for. 30° and 45° are the common choices. 22-1/2° and 10° are for long, gentle offsets.
For more on one angle, see 10°, 22-1/2° and 30°.
Printed or exact
Makers print rounded multipliers so you can do the math in your head. The exact column is the trigonometry. At 45°, Klein prints 1.4 where the exact figure is 1.414.
On a shallow offset the gap is too small to see. On a deep one it adds up. Use the printed figure when you check against the guide that came with your bender, and use the same one for every offset in a run so they match.
Shrink per inch at each angle
Shrink is the length an offset takes out of the stick. Multiply the depth by the shrink per inch for your angle. As Klein prints it for the 56203 on 1/2 inch EMT:
- 10°: 1/16″
- 22-1/2°: 3/16″
- 30°: 1/4″
- 45°: 3/8″
- 60°: 1/2″
Other makers may print different figures for the same angle. Check the chart for your own bender: Klein, Greenlee or Gardner Bender. The conduit shrink chart has every maker side by side.
Worked example
A 6 inch offset at 45° on a Klein 56203, 1/2 inch EMT, measured from the end of the stick:
- Offset depth
- 6″
- Bend angle
- 45°
| Mark | From the end | Line up with | Bend | Direction |
|---|---|---|---|---|
| 1 | 8-3/8″ | Arrow | 45° | First bend |
| 2 | 16-13/16″ | Arrow | 45° | Roll the conduit 180° |
- Multiplier
- 1.4
- Shrink per inch of depth
- 3/8″
- Distance between bends
- 8-3/8″
- Shrink
- 2-1/4″
Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.
Calculate this bend in Bendbook. Pick your bender, type your measurements, and every mark is drawn on the stick for you.
The distance between the marks is the depth times the 45° multiplier. Both marks go on the arrow, and the one nearest the end is bent first.
Shrink: where it matters
What you do with shrink depends on which way you are working.
- Working away from a fixed end: shrink does not move your marks. It makes the run past the offset shorter, so allow for it when you cut the stick.
- Working toward a fixed point, such as a box or an obstacle: the marks have to put the full depth at that point, so they move. Use the marks from a layout that measures to the obstacle, like this one, with the obstacle 48 inches from the end, measured to the far bend:
- Offset depth
- 6″
- Bend angle
- 45°
- Distance to the obstacle
- 48″
| Mark | From the end | Line up with | Bend | Direction |
|---|---|---|---|---|
| 1 | 50-1/4″ | Arrow | 45° | First bend |
| 2 | 41-7/8″ | Arrow | 45° | Roll the conduit 180° |
- Multiplier
- 1.4
- Shrink per inch of depth
- 3/8″
- Distance between bends
- 8-3/8″
- Shrink
- 2-1/4″
Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.
The far mark is the obstacle distance plus the shrink, 3/8″ for every inch of depth. The near mark is the distance between bends back toward the end. Bend the far mark first.
Steps
- Decide the angle. Use 30° or 45° unless you have a reason to go gentler or steeper.
- Measure the depth of the offset, the distance the conduit has to move over.
- Multiply the depth by the multiplier for your angle and your bender. That is the distance between the marks.
- Working away from a fixed end, make the first mark where the offset should start, measured from that end. Make the second mark the distance between bends past it.
- Working toward an obstacle, add the shrink to the distance to the obstacle. That is the far mark. Make the near mark the distance between bends back toward the end.
- Line the mark you bend first up with the arrow and bend to the angle. The degree lines only show how far you have gone.
- Take the stick out and roll it exactly half a turn, 180°.
- Line the other mark up with the arrow and bend to the same angle.
- Lay the stick on a flat floor. Both legs should lie flat and run parallel.
Mistakes that cost a stick
- Mixing printed and exact multipliers in the same run. Pick one and keep to it.
- Using another maker's multiplier. Use the figure for your bender and your conduit.
- Measuring from the wrong end. Work out which end is fixed before you mark.
- Forgetting shrink when working toward an obstacle. The offset comes up short of the point you wanted.
- Rolling a bit less or a bit more than half a turn. That is a dog leg.
- Lining a mark up with a degree line. The marks go on the arrow.
Questions
Which angle should I use for an offset?
Use 30° or 45° for most work. A smaller angle gives a longer, gentler offset and less shrink, but needs more room. A larger angle is shorter but costs more shrink. Count the bends between pull points against the NEC: 358.24 covers EMT and 344.24 covers rigid metal conduit.
Why do two benders give different multipliers for the same angle?
Makers do not all print the same rounded figures. Use the one printed for your bender, and compare only between benders of the same conduit type and size.
Do I add the shrink to my measurement?
Only to the distance to an obstacle you are bending toward, and then the far mark goes there. Working away from a fixed end, shrink changes only where you cut the stick.
Where do I go for matching offsets, kicks and saddles?
See parallel offsets, rolling offsets at 45°, kicks and the three-point saddle.
Check against your own bender. The numbers on this page use the values the maker publishes for the bender named; where the maker prints none, they are worked out from the geometry of the bend. Shoes wear, conduit varies and springback differs, so make one test bend and adjust before you bend the run.