10 degree offset multiplier and how to use it

Reference · Published November 8, 2026

Offset multiplier at 10°

6

Multiply the offset depth by this to get the distance between bends, as Klein prints it.

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.

Offset on a Klein 56203, 1/2″ EMT: mark 1 at 6″, mark 2 at 12″12″6″END12END12
Offset on a Klein 56203, 1/2″ EMT: mark 1 at 6″, mark 2 at 12″. Numbered in bending order.
Bendbook’s bender list, with a Klein 3/4″ EMT bender picked

Your own marks

Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.

The multiplier for a 10° offset is 6. Multiply the depth of the offset by it to get the distance between your two bends. A 10° offset is long and shallow, so it needs a lot of straight stick, but it barely shortens the run.

The multiplier at 10 degrees

The multiplier is the distance between bends for every inch of offset depth. The shallower the angle, the bigger the multiplier and the farther apart the marks sit. At 10° it is the largest of the common angles, which is why this bend suits shallow offsets, like a box offset, or runs with room to spare.

AngleExact multiplierGardner Bender printsGreenlee printsKlein prints
5°11.474———
10°5.759666
15°3.864—3.86—
22-1/2°2.6132.62.62.6
30°2222
45°1.4141.41.41.4
60°1.1551.21.21.2

Shrink goes the other way. At 10° it is 1/16″ for each inch of depth, so a 10° offset costs very little length. For the other angles, see 22-1/2 degrees and 30 degrees, and the shrink chart for shrink at every angle.

Worked example: a 1 inch offset

A 1 inch offset in 1/2 inch EMT on a Klein 56203, measured from the end of the stick, with the figures printed in Klein's guide.

Worked exampleOffset on a Klein 56203, 1/2″ EMT, numbers as printed in the maker’s guide
Offset depth
1″
Bend angle
10°
MarkFrom the endLine up withBendDirection
16″Arrow10°First bend
212″Arrow10°Roll the conduit 180°
Multiplier
6
Shrink per inch of depth
1/16″
Distance between bends
6″
Shrink
1/16″

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.

Calculate this bend in Bendbook. Pick your bender, type your measurements, and every mark is drawn on the stick for you.

Both marks go on the arrow, and the one nearest the end is bent first. Because the distance between bends grows with the depth, a deeper offset at 10° quickly eats a long stretch of straight stick. Work the distance out and check the stick is long enough before you mark it.

Steps

  1. Measure the depth of the offset: how far the conduit has to move over.
  2. Multiply the depth by the 10° multiplier, 6. That is the distance between the marks.
  3. Make the first mark where the offset should start, measured from the end you are working from.
  4. Make the second mark the distance between bends past the first, away from the end.
  5. Line the first mark up with the arrow and bend to 10°. The degree lines only show how far the bend has gone.
  6. Take the stick out and roll it exactly half a turn, 180°.
  7. Line the second mark up with the arrow and bend to 10° again.
  8. Lay the stick on a flat floor. Both legs should lie flat and run parallel, set apart by the depth you wanted.

Placing the offset at an obstacle

When you work toward a fixed point, such as a box or an obstacle, the marks have to put the full depth at that point, so they move. Here is a 3 inch offset at 10° with the obstacle 24 inches from the end, measured to the far bend.

Worked exampleOffset on a Klein 56203, 1/2″ EMT, numbers as printed in the maker’s guide
Offset depth
3″
Bend angle
10°
Distance to the obstacle
24″
MarkFrom the endLine up withBendDirection
124-3/16″Arrow10°First bend
26-3/16″Arrow10°Roll the conduit 180°
Multiplier
6
Shrink per inch of depth
1/16″
Distance between bends
18″
Shrink
3/16″

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.

The far mark is the obstacle distance plus the shrink, 1/16″ for every inch of depth. The near mark is the distance between bends back toward the end. Bend the far mark first. At 10° the shrink is small, but it is still what puts the full depth at the obstacle.

When you work away from a fixed end, shrink does not move the marks. It only shortens the run past the offset, so it matters when you cut the stick.

Mistakes that cost a stick

  • A dog leg. Rolling anything other than half a turn, 180°, between bends leaves the two legs out of line.
  • Measuring from the wrong end. Take both marks from the same end, and check which way the offset has to kick before the first bend.
  • Running short of stick. The long distance between bends at 10° eats straight conduit. Do the layout before you cut.
  • Ignoring shrink toward an obstacle. Add it to the distance to the obstacle for the far mark.
  • Over-bending. Stop at 10°. At this angle a few degrees too much changes the depth a lot.

Questions

When should I use a 10 degree offset instead of a steeper one?

Use it when the offset is shallow and the run is long, or when you want the least drag on the wire pull and the least shrink. Steeper angles fit tight spaces better. A box offset is the usual case.

Is the multiplier the same on every bender?

Every maker in the table above prints the same figure at 10°. Check it against the guide for the bender you actually hold all the same. See the Klein, Greenlee and Gardner Bender chart pages.

Does a 10 degree offset need shrink added?

Only toward a fixed point, and then to the distance to the obstacle, as the obstacle example shows. Away from a fixed end, shrink only affects the cut length.

Can I use 10 degrees for a saddle?

Saddles use their own angles and rules. See the three-point saddle and four-point saddle guides.

Check against your own bender. The numbers on this page use the values the maker publishes for the bender named; where the maker prints none, they are worked out from the geometry of the bend. Shoes wear, conduit varies and springback differs, so make one test bend and adjust before you bend the run.