Greenlee conduit bender chart: take-up, multipliers and marks
Bender charts · Published November 8, 2026
Take-up, Greenlee 840A, 1/2″ EMT
5″
Subtract it from the stub height you want. The result is your mark, measured from the end of the stick.
Bender values: Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4.

Your own marks
Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.
A Greenlee bender chart gives the take-up, the stub marks, the multipliers and the offset marks for one bender and one conduit size, as Greenlee publishes them. Find the bender and size you are holding below and read the chart for that pair. These are the figures to check against the head in your hand.
Which chart to read
Take-up changes with conduit size, so each size has its own bender and its own chart. Match the model stamped on the head and the trade size of the EMT. Do not read the 840A chart for an 841A bender, or the other way round. Greenlee's other EMT heads, the 840F to 843F and the 844A, are listed in the hand bender take-up chart.
Greenlee 840A, 1/2 inch EMT
Greenlee 840A, 1/2″ EMT: the published values
| Value | Published | Source |
|---|---|---|
| Take-up (deduct) for a 90° stub | 5″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Centerline radius | 4-3/16″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
Greenlee 840A, 1/2″ EMT: where to mark a 90° stub
| Stub height | Mark from the end | Line up with |
|---|---|---|
| 8″ | 3″ | Arrow |
| 10″ | 5″ | Arrow |
| 12″ | 7″ | Arrow |
| 14″ | 9″ | Arrow |
| 16″ | 11″ | Arrow |
| 18″ | 13″ | Arrow |
| 20″ | 15″ | Arrow |
| 24″ | 19″ | Arrow |
| 30″ | 25″ | Arrow |
Greenlee 840A, 1/2″ EMT: offset multipliers and shrink
| Angle | Multiplier (printed) | Multiplier (exact) | Shrink per inch (printed) | Shrink per inch (exact) |
|---|---|---|---|---|
| 10° | 6 | 5.759 | 1/16″ | 1/16″ |
| 15° | 3.86 | 3.864 | 1/8″ | 1/8″ |
| 22-1/2° | 2.6 | 2.613 | 3/16″ | 3/16″ |
| 30° | 2 | 2 | 1/4″ | 1/4″ |
| 45° | 1.4 | 1.414 | 3/8″ | 7/16″ |
| 60° | 1.2 | 1.155 | 1/2″ | 9/16″ |
Printed values: Greenlee Use Guide, Site-Rite 840–844 hand benders, page 9.
Greenlee 840A, 1/2″ EMT: offsets, distance between bends and shrink
| Depth | 22-1/2° | 30° | 45° |
|---|---|---|---|
| 2″ | 5-3/16″ apart, 3/8″ shrink | 4″ apart, 1/2″ shrink | 2-13/16″ apart, 3/4″ shrink |
| 3″ | 7-13/16″ apart, 9/16″ shrink | 6″ apart, 3/4″ shrink | 4-3/16″ apart, 1-1/8″ shrink |
| 4″ | 10-3/8″ apart, 3/4″ shrink | 8″ apart, 1″ shrink | 5-5/8″ apart, 1-1/2″ shrink |
| 5″ | 13″ apart, 15/16″ shrink | 10″ apart, 1-1/4″ shrink | 7″ apart, 1-7/8″ shrink |
| 6″ | 15-5/8″ apart, 1-1/8″ shrink | 12″ apart, 1-1/2″ shrink | 8-3/8″ apart, 2-1/4″ shrink |
| 8″ | 20-13/16″ apart, 1-1/2″ shrink | 16″ apart, 2″ shrink | 11-3/16″ apart, 3″ shrink |
| 10″ | 26″ apart, 1-7/8″ shrink | 20″ apart, 2-1/2″ shrink | 14″ apart, 3-3/4″ shrink |
Where the maker prints no value for an angle, the exact geometry is shown.
Calculate this bend in Bendbook. Pick your bender, type your measurements, and every mark is drawn on the stick for you.
Greenlee 841A, 3/4 inch EMT
Greenlee 841A, 3/4″ EMT: the published values
| Value | Published | Source |
|---|---|---|
| Take-up (deduct) for a 90° stub | 6″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Centerline radius | 5-1/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
Greenlee 841A, 3/4″ EMT: where to mark a 90° stub
| Stub height | Mark from the end | Line up with |
|---|---|---|
| 8″ | 2″ | Arrow |
| 10″ | 4″ | Arrow |
| 12″ | 6″ | Arrow |
| 14″ | 8″ | Arrow |
| 16″ | 10″ | Arrow |
| 18″ | 12″ | Arrow |
| 20″ | 14″ | Arrow |
| 24″ | 18″ | Arrow |
| 30″ | 24″ | Arrow |
Greenlee 841A, 3/4″ EMT: offset multipliers and shrink
| Angle | Multiplier (printed) | Multiplier (exact) | Shrink per inch (printed) | Shrink per inch (exact) |
|---|---|---|---|---|
| 10° | 6 | 5.759 | 1/16″ | 1/16″ |
| 15° | 3.86 | 3.864 | 1/8″ | 1/8″ |
| 22-1/2° | 2.6 | 2.613 | 3/16″ | 3/16″ |
| 30° | 2 | 2 | 1/4″ | 1/4″ |
| 45° | 1.4 | 1.414 | 3/8″ | 7/16″ |
| 60° | 1.2 | 1.155 | 1/2″ | 9/16″ |
Printed values: Greenlee Use Guide, Site-Rite 840–844 hand benders, page 9.
Greenlee 841A, 3/4″ EMT: offsets, distance between bends and shrink
| Depth | 22-1/2° | 30° | 45° |
|---|---|---|---|
| 2″ | 5-3/16″ apart, 3/8″ shrink | 4″ apart, 1/2″ shrink | 2-13/16″ apart, 3/4″ shrink |
| 3″ | 7-13/16″ apart, 9/16″ shrink | 6″ apart, 3/4″ shrink | 4-3/16″ apart, 1-1/8″ shrink |
| 4″ | 10-3/8″ apart, 3/4″ shrink | 8″ apart, 1″ shrink | 5-5/8″ apart, 1-1/2″ shrink |
| 5″ | 13″ apart, 15/16″ shrink | 10″ apart, 1-1/4″ shrink | 7″ apart, 1-7/8″ shrink |
| 6″ | 15-5/8″ apart, 1-1/8″ shrink | 12″ apart, 1-1/2″ shrink | 8-3/8″ apart, 2-1/4″ shrink |
| 8″ | 20-13/16″ apart, 1-1/2″ shrink | 16″ apart, 2″ shrink | 11-3/16″ apart, 3″ shrink |
| 10″ | 26″ apart, 1-7/8″ shrink | 20″ apart, 2-1/2″ shrink | 14″ apart, 3-3/4″ shrink |
Where the maker prints no value for an angle, the exact geometry is shown.
Greenlee 842A, 1 inch EMT
Greenlee 842A, 1″ EMT: the published values
| Value | Published | Source |
|---|---|---|
| Take-up (deduct) for a 90° stub | 8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Centerline radius | 6-1/2″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
Greenlee 842A, 1″ EMT: where to mark a 90° stub
| Stub height | Mark from the end | Line up with |
|---|---|---|
| 10″ | 2″ | Arrow |
| 12″ | 4″ | Arrow |
| 14″ | 6″ | Arrow |
| 16″ | 8″ | Arrow |
| 18″ | 10″ | Arrow |
| 20″ | 12″ | Arrow |
| 24″ | 16″ | Arrow |
| 30″ | 22″ | Arrow |
Greenlee 842A, 1″ EMT: offset multipliers and shrink
| Angle | Multiplier (printed) | Multiplier (exact) | Shrink per inch (printed) | Shrink per inch (exact) |
|---|---|---|---|---|
| 10° | 6 | 5.759 | 1/16″ | 1/16″ |
| 15° | 3.86 | 3.864 | 1/8″ | 1/8″ |
| 22-1/2° | 2.6 | 2.613 | 3/16″ | 3/16″ |
| 30° | 2 | 2 | 1/4″ | 1/4″ |
| 45° | 1.4 | 1.414 | 3/8″ | 7/16″ |
| 60° | 1.2 | 1.155 | 1/2″ | 9/16″ |
Printed values: Greenlee Use Guide, Site-Rite 840–844 hand benders, page 9.
Greenlee 842A, 1″ EMT: offsets, distance between bends and shrink
| Depth | 22-1/2° | 30° | 45° |
|---|---|---|---|
| 2″ | 5-3/16″ apart, 3/8″ shrink | 4″ apart, 1/2″ shrink | 2-13/16″ apart, 3/4″ shrink |
| 3″ | 7-13/16″ apart, 9/16″ shrink | 6″ apart, 3/4″ shrink | 4-3/16″ apart, 1-1/8″ shrink |
| 4″ | 10-3/8″ apart, 3/4″ shrink | 8″ apart, 1″ shrink | 5-5/8″ apart, 1-1/2″ shrink |
| 5″ | 13″ apart, 15/16″ shrink | 10″ apart, 1-1/4″ shrink | 7″ apart, 1-7/8″ shrink |
| 6″ | 15-5/8″ apart, 1-1/8″ shrink | 12″ apart, 1-1/2″ shrink | 8-3/8″ apart, 2-1/4″ shrink |
| 8″ | 20-13/16″ apart, 1-1/2″ shrink | 16″ apart, 2″ shrink | 11-3/16″ apart, 3″ shrink |
| 10″ | 26″ apart, 1-7/8″ shrink | 20″ apart, 2-1/2″ shrink | 14″ apart, 3-3/4″ shrink |
Where the maker prints no value for an angle, the exact geometry is shown.
Greenlee 843A, 1-1/4 inch EMT
Greenlee 843A, 1-1/4″ EMT: the published values
| Value | Published | Source |
|---|---|---|
| Take-up (deduct) for a 90° stub | 11″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Centerline radius | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
Greenlee 843A, 1-1/4″ EMT: where to mark a 90° stub
| Stub height | Mark from the end | Line up with |
|---|---|---|
| 12″ | 1″ | Arrow |
| 14″ | 3″ | Arrow |
| 16″ | 5″ | Arrow |
| 18″ | 7″ | Arrow |
| 20″ | 9″ | Arrow |
| 24″ | 13″ | Arrow |
| 30″ | 19″ | Arrow |
Greenlee 843A, 1-1/4″ EMT: offset multipliers and shrink
| Angle | Multiplier (printed) | Multiplier (exact) | Shrink per inch (printed) | Shrink per inch (exact) |
|---|---|---|---|---|
| 10° | 6 | 5.759 | 1/16″ | 1/16″ |
| 15° | 3.86 | 3.864 | 1/8″ | 1/8″ |
| 22-1/2° | 2.6 | 2.613 | 3/16″ | 3/16″ |
| 30° | 2 | 2 | 1/4″ | 1/4″ |
| 45° | 1.4 | 1.414 | 3/8″ | 7/16″ |
| 60° | 1.2 | 1.155 | 1/2″ | 9/16″ |
Printed values: Greenlee Use Guide, Site-Rite 840–844 hand benders, page 9.
Greenlee 843A, 1-1/4″ EMT: offsets, distance between bends and shrink
| Depth | 22-1/2° | 30° | 45° |
|---|---|---|---|
| 2″ | 5-3/16″ apart, 3/8″ shrink | 4″ apart, 1/2″ shrink | 2-13/16″ apart, 3/4″ shrink |
| 3″ | 7-13/16″ apart, 9/16″ shrink | 6″ apart, 3/4″ shrink | 4-3/16″ apart, 1-1/8″ shrink |
| 4″ | 10-3/8″ apart, 3/4″ shrink | 8″ apart, 1″ shrink | 5-5/8″ apart, 1-1/2″ shrink |
| 5″ | 13″ apart, 15/16″ shrink | 10″ apart, 1-1/4″ shrink | 7″ apart, 1-7/8″ shrink |
| 6″ | 15-5/8″ apart, 1-1/8″ shrink | 12″ apart, 1-1/2″ shrink | 8-3/8″ apart, 2-1/4″ shrink |
| 8″ | 20-13/16″ apart, 1-1/2″ shrink | 16″ apart, 2″ shrink | 11-3/16″ apart, 3″ shrink |
| 10″ | 26″ apart, 1-7/8″ shrink | 20″ apart, 2-1/2″ shrink | 14″ apart, 3-3/4″ shrink |
Where the maker prints no value for an angle, the exact geometry is shown.
Using the stub marks
The stub mark is the stub height less the take-up, measured from the end of the stick that will rise. It lines up with the arrow. Here is a 12 inch stub on the 840A:
- Stub height
- 12″
| Mark | From the end | Line up with | Bend | Direction |
|---|---|---|---|---|
| 1 | 7″ | Arrow | 90° | First bend |
- Take-up
- 5″
- Gain
- 1-13/16″
Bender values: Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4.
The stub rises from the end you measured from. Check that before you bend. For the full method, see how to bend a 90 degree stub-up.
Using the multipliers
The multiplier turns the depth of an offset into the distance between the two bends. At 30° Greenlee prints 2, with a shrink of 1/4″ for every inch of depth. Here is a 6 inch offset at 30° on the 840A:
- Offset depth
- 6″
- Bend angle
- 30°
| Mark | From the end | Line up with | Bend | Direction |
|---|---|---|---|---|
| 1 | 12″ | Arrow | 30° | First bend |
| 2 | 24″ | Arrow | 30° | Roll the conduit 180° |
- Multiplier
- 2
- Shrink per inch of depth
- 1/4″
- Distance between bends
- 12″
- Shrink
- 1-1/2″
- Gain
- 1/8″
Bender values: Greenlee Use Guide, Site-Rite 840–844 hand benders, page 9; Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4.
Working away from a fixed end, shrink does not move your marks. It makes the run past the offset shorter, so it matters when you cut the stick. For other angles, see the offset multiplier for 22-1/2 degrees, the offset multiplier for 30 degrees and the offset multiplier for 10 degrees. The full list of shrink values is in conduit shrink per inch of offset.
Steps
For a stub:
- Find your bender model and EMT size above.
- Subtract the take-up for your bender from the stub height. On the 840A that is 5″.
- Mark the stick that far from the end that will rise.
- Line the mark up with the arrow and pull to 90°. Check it with a level.
For an offset:
- Multiply the depth by the multiplier for your angle. At 30° that is 2 × the depth.
- Make the first mark where the offset is to start. Make the second mark that distance further along the stick.
- Line the first mark up with the arrow and bend to the angle.
- Take the stick out and roll it exactly half a turn (180°).
- Line the second mark up with the arrow and bend to the same angle.
- Lay the stick on a flat floor and check that both legs lie flat.
Mistakes that cost a stick
- Reading the wrong chart. A value from one bender used on a different size puts every mark in the wrong place.
- Measuring from the wrong end. The stub rises from the end you measured from. Confirm which end that is before you mark.
- Rolling less or more than half a turn. That gives a dog leg, not an offset.
- Lining a mark up with a degree line. The degree lines show how far the bend has gone. Stub and offset marks go on the arrow.
- Forgetting shrink when you work toward a fixed point. The marks must put the full depth at the obstacle, not short of it. See the shrink chart.
- Over-bending. Stop at the angle on the head, then check it.
Questions
Is the chart the same for every Greenlee bender?
No. Each model and conduit size has its own take-up and stub marks. The 840A, 841A, 842A and 843A cover different EMT sizes, so the same stub gives a different mark on each. The multipliers and shrink per inch are the same on all four, because they depend on the angle, not the size.
Can I use the EMT chart for rigid conduit?
No. These charts are for EMT. Rigid has its own take-up on each bender that bends it, and the values are not interchangeable.
Why do printed values differ from exact ones?
Some of the maker's printed figures are rounded. At 45° Greenlee prints a shrink of 3/8″ per inch, where exact trigonometry gives 7/16″. At 60° the printed multiplier is 1.2 against an exact 1.155. The printed values are what you check against the bender in hand.
Do these marks work for saddles and kicks?
The charts cover stubs and offsets. For other bends, see how to bend a three-point saddle, how to bend a four-point saddle and how to bend a kick in conduit. The full list is in the guides index.
Check against your own bender. The numbers on this page use the values the maker publishes for the bender named; where the maker prints none, they are worked out from the geometry of the bend. Shoes wear, conduit varies and springback differs, so make one test bend and adjust before you bend the run.