Offset multiplier for 22-1/2 degrees: printed and exact

Reference · Published November 8, 2026

Offset multiplier at 22-1/2°

2.6

Multiply the offset depth by this to get the distance between bends, as Klein prints it.

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.

Offset on a Klein 56203, 1/2″ EMT: mark 1 at 13″, mark 2 at 26″26″13″END12END12
Offset on a Klein 56203, 1/2″ EMT: mark 1 at 13″, mark 2 at 26″. Numbered in bending order.
Bendbook’s bender list, with a Klein 3/4″ EMT bender picked

Your own marks

Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.

The multiplier for a 22-1/2° offset is 2.6, as printed in the maker's guide. Multiply the depth of the offset by it to get the distance between the two bends. The shrink is 3/16″ for every inch of depth.

Printed and exact

The printed multiplier is the figure in the maker's guide. It is rounded so you can work it in your head and check it against the bender in hand. The exact multiplier comes from trigonometry and is not rounded.

AngleExact multiplierGardner Bender printsGreenlee printsKlein prints
5°11.474———
10°5.759666
15°3.864—3.86—
22-1/2°2.6132.62.62.6
30°2222
45°1.4141.41.41.4
60°1.1551.21.21.2

At 22-1/2° the exact multiplier is 2.613. The difference from the printed figure is small. Multiplied by a deep offset it moves the second mark a little, so use one or the other for a whole run, not both. The shrink per inch comes out the same printed and exact at this angle.

Use the printed figure when you check against the bender or the maker's guide. For other angles, see the 30 degree and 10 degree pages, or every angle side by side.

Worked example: a 5 inch offset

A 5 inch offset in 1/2 inch EMT on a Klein 56203, measured from the end of the stick, with printed figures.

Worked exampleOffset on a Klein 56203, 1/2″ EMT, numbers as printed in the maker’s guide
Offset depth
5″
Bend angle
22-1/2°
MarkFrom the endLine up withBendDirection
113″Arrow22-1/2°First bend
226″Arrow22-1/2°Roll the conduit 180°
Multiplier
2.6
Shrink per inch of depth
3/16″
Distance between bends
13″
Shrink
15/16″

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.

Calculate this bend in Bendbook. Pick your bender, type your measurements, and every mark is drawn on the stick for you.

Both marks go on the arrow, and the one nearest the end is bent first.

Where shrink matters

Shrink does not move your marks when you work away from a fixed end. It only makes the run past the offset shorter. That matters when you cut the stick, so measure for the cut after you bend.

When you work toward a fixed point, such as an obstacle or a box, the marks must put the full depth at that point. Here is a 5 inch offset to an obstacle 36 inches from the end, measured to the far bend.

Worked exampleOffset on a Klein 56203, 1/2″ EMT, numbers as printed in the maker’s guide
Offset depth
5″
Bend angle
22-1/2°
Distance to the obstacle
36″
MarkFrom the endLine up withBendDirection
136-15/16″Arrow22-1/2°First bend
223-15/16″Arrow22-1/2°Roll the conduit 180°
Multiplier
2.6
Shrink per inch of depth
3/16″
Distance between bends
13″
Shrink
15/16″

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.

The far mark is the obstacle distance plus the shrink for the whole offset. The near mark is the distance between bends back toward the end. Bend the far mark first.

Steps

  1. Measure the depth of the offset, and the distance to the obstacle if there is one.
  2. Multiply the depth by the 22-1/2° multiplier, 2.6. That is the distance between the marks.
  3. Working away from a fixed end, make the first mark where the offset should start, measured from that end. Make the second mark the distance between bends past it.
  4. Working toward an obstacle, multiply the depth by the shrink, 3/16″ per inch, and add it to the distance to the obstacle. That is the far mark. Make the near mark the distance between bends back toward the end.
  5. Line the mark you bend first up with the arrow and bend to 22-1/2°.
  6. Take the stick out and roll it exactly half a turn, 180°.
  7. Line the other mark up with the arrow and bend to 22-1/2° again.
  8. Lay the stick on a flat floor. Both legs should lie flat, with no twist.
  9. Check the depth against the obstacle before you hang it.

Mistakes that cost a stick

  • Dog leg. If you roll anything other than half a turn between the bends, the legs do not line up. Roll exactly 180°.
  • Measuring from the wrong end. Take both marks from the same end.
  • Forgetting shrink at an obstacle. Working toward a fixed point, the far mark goes past the obstacle distance by the shrink. Do not reuse the marks from an offset in open space.
  • Over-bending. Go to 22-1/2° and stop. A bend that is a little over will not match its partner.
  • Lining a mark up with a degree line. The marks go on the arrow. The degree lines only show how far you have gone.

Questions

Why use 22-1/2° instead of 30° or 45°?

A shallower angle makes a longer, gentler offset. It is easier on the wire and uses more length. A steeper angle fits a tighter space. See the 30 degree multiplier for the steeper case.

Is the printed multiplier wrong?

No. It is rounded on purpose so the marks are quick to work. On a shallow offset the difference is too small to see. Use the exact figure only if you want to see how far the rounding moves a mark on a deep one.

Does the multiplier change with the bender?

The geometry of the offset is the same, but the printed figures come from each maker's guide. The table above shows what each one prints. For everything else on your bender, use its chart: Klein, Greenlee or Gardner Bender.

Can I use this for a saddle?

Not directly. A saddle has its own angles and marks. See the three-point saddle and four-point saddle guides.

Check against your own bender. The numbers on this page use the values the maker publishes for the bender named; where the maker prints none, they are worked out from the geometry of the bend. Shoes wear, conduit varies and springback differs, so make one test bend and adjust before you bend the run.