Gardner Bender conduit bender chart: take-up, multipliers and marks
Bender charts · Published November 8, 2026
Take-up, Gardner Bender 960, 1/2″ EMT
5″
Subtract it from the stub height you want. The result is your mark, measured from the end of the stick.
Bender values: Gardner Bender Hand Bender How To Guide (960/961/962), page 1.

Your own marks
Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.
Gardner Bender makes its EMT hand benders by size: the 960 for 1/2 inch EMT, the 961 for 3/4 inch EMT and the 962 for 1 inch EMT. Each has its own published take-up and stub marks. The charts below show those values with the multipliers and offsets, and the examples show how the marks go on a stick.
The charts
Take-up changes with conduit size, so read the chart for the bender and size in your hand. Do not carry a take-up from one size to another. The multipliers and shrink per inch are the same on all three, because they depend on the angle, not the size.
Gardner Bender 960, 1/2 inch EMT
Gardner Bender 960, 1/2″ EMT: the published values
| Value | Published | Source |
|---|---|---|
| Take-up (deduct) for a 90° stub | 5″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
| Centerline radius | 3-11/16″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
Gardner Bender 960, 1/2″ EMT: where to mark a 90° stub
| Stub height | Mark from the end | Line up with |
|---|---|---|
| 8″ | 3″ | Arrow |
| 10″ | 5″ | Arrow |
| 12″ | 7″ | Arrow |
| 14″ | 9″ | Arrow |
| 16″ | 11″ | Arrow |
| 18″ | 13″ | Arrow |
| 20″ | 15″ | Arrow |
| 24″ | 19″ | Arrow |
| 30″ | 25″ | Arrow |
Gardner Bender 960, 1/2″ EMT: offset multipliers and shrink
| Angle | Multiplier (printed) | Multiplier (exact) | Shrink per inch (printed) | Shrink per inch (exact) |
|---|---|---|---|---|
| 10° | 6 | 5.759 | 1/16″ | 1/16″ |
| 22-1/2° | 2.6 | 2.613 | 3/16″ | 3/16″ |
| 30° | 2 | 2 | 1/4″ | 1/4″ |
| 45° | 1.4 | 1.414 | 3/8″ | 7/16″ |
| 60° | 1.2 | 1.155 | 1/2″ | 9/16″ |
Printed values: Gardner Bender Hand Bender How To Guide (960/961/962), page 2.
Gardner Bender 960, 1/2″ EMT: offsets, distance between bends and shrink
| Depth | 22-1/2° | 30° | 45° |
|---|---|---|---|
| 2″ | 5-3/16″ apart, 3/8″ shrink | 4″ apart, 1/2″ shrink | 2-13/16″ apart, 3/4″ shrink |
| 3″ | 7-13/16″ apart, 9/16″ shrink | 6″ apart, 3/4″ shrink | 4-3/16″ apart, 1-1/8″ shrink |
| 4″ | 10-3/8″ apart, 3/4″ shrink | 8″ apart, 1″ shrink | 5-5/8″ apart, 1-1/2″ shrink |
| 5″ | 13″ apart, 15/16″ shrink | 10″ apart, 1-1/4″ shrink | 7″ apart, 1-7/8″ shrink |
| 6″ | 15-5/8″ apart, 1-1/8″ shrink | 12″ apart, 1-1/2″ shrink | 8-3/8″ apart, 2-1/4″ shrink |
| 8″ | 20-13/16″ apart, 1-1/2″ shrink | 16″ apart, 2″ shrink | 11-3/16″ apart, 3″ shrink |
| 10″ | 26″ apart, 1-7/8″ shrink | 20″ apart, 2-1/2″ shrink | 14″ apart, 3-3/4″ shrink |
Where the maker prints no value for an angle, the exact geometry is shown.
Calculate this bend in Bendbook. Pick your bender, type your measurements, and every mark is drawn on the stick for you.
Gardner Bender 961, 3/4 inch EMT
Gardner Bender 961, 3/4″ EMT: the published values
| Value | Published | Source |
|---|---|---|
| Take-up (deduct) for a 90° stub | 6″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
| Centerline radius | 4-3/4″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
Gardner Bender 961, 3/4″ EMT: where to mark a 90° stub
| Stub height | Mark from the end | Line up with |
|---|---|---|
| 8″ | 2″ | Arrow |
| 10″ | 4″ | Arrow |
| 12″ | 6″ | Arrow |
| 14″ | 8″ | Arrow |
| 16″ | 10″ | Arrow |
| 18″ | 12″ | Arrow |
| 20″ | 14″ | Arrow |
| 24″ | 18″ | Arrow |
| 30″ | 24″ | Arrow |
Gardner Bender 961, 3/4″ EMT: offset multipliers and shrink
| Angle | Multiplier (printed) | Multiplier (exact) | Shrink per inch (printed) | Shrink per inch (exact) |
|---|---|---|---|---|
| 10° | 6 | 5.759 | 1/16″ | 1/16″ |
| 22-1/2° | 2.6 | 2.613 | 3/16″ | 3/16″ |
| 30° | 2 | 2 | 1/4″ | 1/4″ |
| 45° | 1.4 | 1.414 | 3/8″ | 7/16″ |
| 60° | 1.2 | 1.155 | 1/2″ | 9/16″ |
Printed values: Gardner Bender Hand Bender How To Guide (960/961/962), page 2.
Gardner Bender 961, 3/4″ EMT: offsets, distance between bends and shrink
| Depth | 22-1/2° | 30° | 45° |
|---|---|---|---|
| 2″ | 5-3/16″ apart, 3/8″ shrink | 4″ apart, 1/2″ shrink | 2-13/16″ apart, 3/4″ shrink |
| 3″ | 7-13/16″ apart, 9/16″ shrink | 6″ apart, 3/4″ shrink | 4-3/16″ apart, 1-1/8″ shrink |
| 4″ | 10-3/8″ apart, 3/4″ shrink | 8″ apart, 1″ shrink | 5-5/8″ apart, 1-1/2″ shrink |
| 5″ | 13″ apart, 15/16″ shrink | 10″ apart, 1-1/4″ shrink | 7″ apart, 1-7/8″ shrink |
| 6″ | 15-5/8″ apart, 1-1/8″ shrink | 12″ apart, 1-1/2″ shrink | 8-3/8″ apart, 2-1/4″ shrink |
| 8″ | 20-13/16″ apart, 1-1/2″ shrink | 16″ apart, 2″ shrink | 11-3/16″ apart, 3″ shrink |
| 10″ | 26″ apart, 1-7/8″ shrink | 20″ apart, 2-1/2″ shrink | 14″ apart, 3-3/4″ shrink |
Where the maker prints no value for an angle, the exact geometry is shown.
Gardner Bender 962, 1 inch EMT
Gardner Bender 962, 1″ EMT: the published values
| Value | Published | Source |
|---|---|---|
| Take-up (deduct) for a 90° stub | 8″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
| Centerline radius | 5-13/16″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
Gardner Bender 962, 1″ EMT: where to mark a 90° stub
| Stub height | Mark from the end | Line up with |
|---|---|---|
| 10″ | 2″ | Arrow |
| 12″ | 4″ | Arrow |
| 14″ | 6″ | Arrow |
| 16″ | 8″ | Arrow |
| 18″ | 10″ | Arrow |
| 20″ | 12″ | Arrow |
| 24″ | 16″ | Arrow |
| 30″ | 22″ | Arrow |
Gardner Bender 962, 1″ EMT: offset multipliers and shrink
| Angle | Multiplier (printed) | Multiplier (exact) | Shrink per inch (printed) | Shrink per inch (exact) |
|---|---|---|---|---|
| 10° | 6 | 5.759 | 1/16″ | 1/16″ |
| 22-1/2° | 2.6 | 2.613 | 3/16″ | 3/16″ |
| 30° | 2 | 2 | 1/4″ | 1/4″ |
| 45° | 1.4 | 1.414 | 3/8″ | 7/16″ |
| 60° | 1.2 | 1.155 | 1/2″ | 9/16″ |
Printed values: Gardner Bender Hand Bender How To Guide (960/961/962), page 2.
Gardner Bender 962, 1″ EMT: offsets, distance between bends and shrink
| Depth | 22-1/2° | 30° | 45° |
|---|---|---|---|
| 2″ | 5-3/16″ apart, 3/8″ shrink | 4″ apart, 1/2″ shrink | 2-13/16″ apart, 3/4″ shrink |
| 3″ | 7-13/16″ apart, 9/16″ shrink | 6″ apart, 3/4″ shrink | 4-3/16″ apart, 1-1/8″ shrink |
| 4″ | 10-3/8″ apart, 3/4″ shrink | 8″ apart, 1″ shrink | 5-5/8″ apart, 1-1/2″ shrink |
| 5″ | 13″ apart, 15/16″ shrink | 10″ apart, 1-1/4″ shrink | 7″ apart, 1-7/8″ shrink |
| 6″ | 15-5/8″ apart, 1-1/8″ shrink | 12″ apart, 1-1/2″ shrink | 8-3/8″ apart, 2-1/4″ shrink |
| 8″ | 20-13/16″ apart, 1-1/2″ shrink | 16″ apart, 2″ shrink | 11-3/16″ apart, 3″ shrink |
| 10″ | 26″ apart, 1-7/8″ shrink | 20″ apart, 2-1/2″ shrink | 14″ apart, 3-3/4″ shrink |
Where the maker prints no value for an angle, the exact geometry is shown.
Using the chart for a 90 degree stub
The stub mark is the stub height less the take-up, measured from the end of the stick that will rise. It lines up with the arrow. Here is a 12 inch stub on the 960:
- Stub height
- 12″
| Mark | From the end | Line up with | Bend | Direction |
|---|---|---|---|---|
| 1 | 7″ | Arrow | 90° | First bend |
- Take-up
- 5″
- Gain
- 1-9/16″
Bender values: Gardner Bender Hand Bender How To Guide (960/961/962), page 1.
The stub rises from the end you measured from. Check this before you bend. For more detail, see how to bend a 90 degree stub-up.
Using the chart for an offset
The multiplier gives the distance between the two bends of an offset: depth times multiplier. On the 960 at 30°, the printed multiplier is 2, and the shrink is 1/4″ for every inch of depth.
When you bend toward an obstacle, the marks must put the full depth at the obstacle. Here is a 6 inch offset at 30°, with the obstacle 24 inches from the end, measured to the far bend:
- Offset depth
- 6″
- Bend angle
- 30°
- Distance to the obstacle
- 24″
| Mark | From the end | Line up with | Bend | Direction |
|---|---|---|---|---|
| 1 | 25-1/2″ | Arrow | 30° | First bend |
| 2 | 13-1/2″ | Arrow | 30° | Roll the conduit 180° |
- Multiplier
- 2
- Shrink per inch of depth
- 1/4″
- Distance between bends
- 12″
- Shrink
- 1-1/2″
- Gain
- 1/16″
Bender values: Gardner Bender Hand Bender How To Guide (960/961/962), page 2; Gardner Bender Hand Bender How To Guide (960/961/962), page 1.
The first mark goes past the obstacle by the shrink, so the offset reaches full depth at the obstacle and not short of it. The second mark sits the distance between bends back toward the end. The mark furthest along is bent first.
Working away from a fixed end instead, shrink does not move the marks. It only makes the run past the offset shorter, so allow for it when you cut the stick. For other angles, see the guides on the multiplier for 10 degrees, 22-1/2 degrees and 30 degrees, and the shrink chart.
Steps
For a stub:
- Pick the bender that matches your conduit size.
- Subtract the take-up for that bender from the stub height. On the 960 that is 5″.
- Mark the stick that far from the end that will rise.
- Line the mark up with the arrow and bend until the stub reaches 90°. Check it with a level.
For an offset to an obstacle:
- Measure from the end of the stick to the obstacle.
- Work out the shrink: 1/4″ × the depth at 30°. Add it to the distance to the obstacle. Make the first mark there.
- Work out the distance between bends: 2 × the depth at 30°. Make the second mark that far back toward the end.
- Line the first mark up with the arrow and bend to the angle.
- Take the stick out and roll it exactly half a turn (180°).
- Line the second mark up with the arrow and bend to the same angle.
- Lay the stick on a flat surface and check that it sits flat with no dog leg.
Check every mark against your own bender before you cut. The printed values come from the maker's guide, and a worn head can change the result.
Mistakes that cost a stick
- Dog leg. Rolling anything other than half a turn between the two bends of an offset leaves the conduit twisted.
- Wrong end. Measure every mark from the same end. Measuring from the other end puts the stub on the wrong side.
- Forgetting shrink toward an obstacle. Without it the offset lands short of the obstacle.
- Wrong size chart. The 960, 961 and 962 are for different conduit sizes. Their take-ups are not interchangeable.
- Over-bending. Stop at the angle and check it before you push further.
Questions
Which Gardner Bender fits which EMT size?
The 960 is for 1/2 inch EMT, the 961 for 3/4 inch EMT and the 962 for 1 inch EMT. Use the chart for the one in your hand.
Can I use the take-up of the 960 on larger EMT?
No. Take-up changes with conduit size, so each bender has its own published value. Use the chart for the bender and size you are bending.
Where do I find other brands?
See the Klein chart and the Greenlee chart. For take-up by size, see the guides for 1/2 inch EMT, 3/4 inch EMT and 1 inch EMT, or the take-up chart.
Do these marks work for saddles and kicks?
No. Each bend has its own marks and its own method. See the guides for the three-point saddle, the four-point saddle and the kick.
Check against your own bender. The numbers on this page use the values the maker publishes for the bender named; where the maker prints none, they are worked out from the geometry of the bend. Shoes wear, conduit varies and springback differs, so make one test bend and adjust before you bend the run.