1 inch EMT take-up and bending chart

Bender charts · Published November 8, 2026

Take-up, 1″ EMT

8″

Subtract it from the stub height you want. The result is your mark, measured from the end of the stick.

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2.

90° stub-up on a Klein 56205, 1″ EMT: mark 1 at 4″4″END1END1
90° stub-up on a Klein 56205, 1″ EMT: mark 1 at 4″. Numbered in bending order.
Bendbook’s bender list, with a Klein 3/4″ EMT bender picked

Your own marks

Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.

The take-up for a 1 inch EMT hand bender is 8″. Take-up is the length the bender uses up in a 90°. To bend a stub, subtract the take-up from the stub height you want, mark the stick that far from the end, line the mark up with the arrow and pull to 90°.

Take-up of 1 inch EMT benders

BenderTake-upRadiusSource
Gardner Bender 9628″5-13/16″Gardner Bender Hand Bender How To Guide (960/961/962), page 1
Greenlee 842A8″6-1/2″Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4
Greenlee 842F8″6-1/2″Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4
Ideal 74-003not published——
Ideal 74-033not published——
Klein 562058″—Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2

Every 1 inch EMT bender in this table that publishes a take-up prints the same one, so the mark for a given stub is the same on any of them. The maker publishes no take-up for the Ideal 74-003 and 74-033. If you bend with one of those, use the take-up in the instructions that came with it, or measure your own from a test stub, as described under Questions below.

Do not carry a take-up over from another size. Take-up changes with conduit size, and rigid and IMC differ from EMT. The hand bender take-up chart covers the other sizes.

Where to mark common stubs

The mark is the stub height less the take-up, measured from the end of the stick that will rise.

Stub heightMark from the endLine up with
10″2″Arrow
12″4″Arrow
14″6″Arrow
16″8″Arrow
18″10″Arrow
20″12″Arrow
24″16″Arrow
30″22″Arrow

Take-up 8″: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2.

Worked example: a 12 inch stub

Worked example90° stub-up on a Klein 56205, 1″ EMT, numbers as printed in the maker’s guide
Stub height
12″
MarkFrom the endLine up withBendDirection
14″Arrow90°First bend
Take-up
8″

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2.

Calculate this bend in Bendbook. Pick your bender, type your measurements, and every mark is drawn on the stick for you.

The stub height runs from the end of the stick to the back of the bend, the outside of the 90. That is what the take-up assumes, so measure the finished stub the same way when you check it.

Steps

  1. Measure the stub height you need. Decide which end of the stick will rise.
  2. Subtract the take-up, 8″, from the stub height. Mark the stick that far from the end that will rise.
  3. Draw the mark all the way around the stick, so you can see it from the side.
  4. Seat the stick in the bender with the hook holding it, and slide it until the mark lines up with the arrow.
  5. Before you pull, check that the stub will come up from the end you measured from. If it would come up from the other end, take the stick out and turn it around.
  6. Keep your foot heavy on the heel and pull the handle in one steady motion. The degree lines only show how far the bend has gone.
  7. Stop at 90°. Check the stub with a level before you take the stick out of the bender.
  8. Measure from the end of the stick to the back of the bend.

Mistakes that cost a stick

  • Measuring from the wrong end. Decide which end the stub rises from before you mark, and measure from that end.
  • Using a smaller size's take-up. A smaller take-up puts the mark too far from the end, and the stub comes out tall.
  • Lining the mark up with a degree line. For a stub, the mark goes on the arrow.
  • Over-bending. Past 90° you have to open the bend back up, and 1 inch EMT can kink or flatten when you do. Stop at 90° and check.
  • Forgetting the bend count. Between pull points, EMT is covered by NEC 358.24. Count your bends before you commit.

Questions

What is the take-up for 1 inch EMT?

On every 1 inch EMT bender in the table that publishes one, it is 8″. Find your model in the table and make sure you are reading the 1 inch EMT line.

Is take-up the same for 1 inch rigid?

No. Take-up is given per conduit type and size, and rigid and IMC are not EMT. Use the value for your bender in the conduit you are bending. The hand bender take-up chart lists the rigid values the makers publish.

My bender has no published take-up. What do I do?

Check the instructions or the markings on the bender first. If neither gives one, bend a test stub. Put a mark a known distance from the end, line it up with the arrow and bend a 90. Measure the stub from the end to the back of the bend. The stub height less the distance to your mark is your take-up.

Where can I read more?

The 90 degree stub-up guide covers the bend in more detail. For offsets in this size, see how to bend an offset on 1 inch EMT. For one maker's full chart, see the Klein, Greenlee or Gardner Bender chart pages.

Check against your own bender. The numbers on this page use the values the maker publishes for the bender named; where the maker prints none, they are worked out from the geometry of the bend. Shoes wear, conduit varies and springback differs, so make one test bend and adjust before you bend the run.