Klein bender chart for EMT: take-up, multipliers and marks
Bender charts · Published November 8, 2026
Take-up, Klein 56203, 1/2″ EMT
5″
Subtract it from the stub height you want. The result is your mark, measured from the end of the stick.
Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2.

Your own marks
Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.
A Klein bender chart lists what Klein publishes for one bender and one size of conduit: the take-up, where to mark common stubs, the offset multipliers and shrink, and the distance between bends for common offsets. Each size of EMT has its own bender head and its own chart, so find the one that matches the bender in your hand.
Which Klein bender goes with which EMT
- Klein 56203 bends 1/2″ EMT.
- Klein 56204 bends 3/4″ EMT.
- Klein 56205 bends 1″ EMT.
- Klein 56211 bends 1-1/4″ EMT.
Klein also makes the 56206 for 1/2″ EMT and the 56207 for 3/4″ EMT and 1/2″ rigid. Their take-ups are in the hand bender take-up chart.
Check the model number cast into your bender's head before you read a chart. A chart for the wrong size gives marks that look reasonable and put the bend in the wrong place.
Klein 56203, 1/2″ EMT
Klein 56203, 1/2″ EMT: the published values
| Value | Published | Source |
|---|---|---|
| Take-up (deduct) for a 90° stub | 5″ | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
Klein 56203, 1/2″ EMT: where to mark a 90° stub
| Stub height | Mark from the end | Line up with |
|---|---|---|
| 8″ | 3″ | Arrow |
| 10″ | 5″ | Arrow |
| 12″ | 7″ | Arrow |
| 14″ | 9″ | Arrow |
| 16″ | 11″ | Arrow |
| 18″ | 13″ | Arrow |
| 20″ | 15″ | Arrow |
| 24″ | 19″ | Arrow |
| 30″ | 25″ | Arrow |
Klein 56203, 1/2″ EMT: offset multipliers and shrink
| Angle | Multiplier (printed) | Multiplier (exact) | Shrink per inch (printed) | Shrink per inch (exact) |
|---|---|---|---|---|
| 10° | 6 | 5.759 | 1/16″ | 1/16″ |
| 22-1/2° | 2.6 | 2.613 | 3/16″ | 3/16″ |
| 30° | 2 | 2 | 1/4″ | 1/4″ |
| 45° | 1.4 | 1.414 | 3/8″ | 7/16″ |
| 60° | 1.2 | 1.155 | 1/2″ | 9/16″ |
Printed values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.
Klein 56203, 1/2″ EMT: offsets, distance between bends and shrink
| Depth | 22-1/2° | 30° | 45° |
|---|---|---|---|
| 2″ | 5-3/16″ apart, 3/8″ shrink | 4″ apart, 1/2″ shrink | 2-13/16″ apart, 3/4″ shrink |
| 3″ | 7-13/16″ apart, 9/16″ shrink | 6″ apart, 3/4″ shrink | 4-3/16″ apart, 1-1/8″ shrink |
| 4″ | 10-3/8″ apart, 3/4″ shrink | 8″ apart, 1″ shrink | 5-5/8″ apart, 1-1/2″ shrink |
| 5″ | 13″ apart, 15/16″ shrink | 10″ apart, 1-1/4″ shrink | 7″ apart, 1-7/8″ shrink |
| 6″ | 15-5/8″ apart, 1-1/8″ shrink | 12″ apart, 1-1/2″ shrink | 8-3/8″ apart, 2-1/4″ shrink |
| 8″ | 20-13/16″ apart, 1-1/2″ shrink | 16″ apart, 2″ shrink | 11-3/16″ apart, 3″ shrink |
| 10″ | 26″ apart, 1-7/8″ shrink | 20″ apart, 2-1/2″ shrink | 14″ apart, 3-3/4″ shrink |
Where the maker prints no value for an angle, the exact geometry is shown.
Calculate this bend in Bendbook. Pick your bender, type your measurements, and every mark is drawn on the stick for you.
Klein 56204, 3/4″ EMT
Klein 56204, 3/4″ EMT: the published values
| Value | Published | Source |
|---|---|---|
| Take-up (deduct) for a 90° stub | 6″ | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
Klein 56204, 3/4″ EMT: where to mark a 90° stub
| Stub height | Mark from the end | Line up with |
|---|---|---|
| 8″ | 2″ | Arrow |
| 10″ | 4″ | Arrow |
| 12″ | 6″ | Arrow |
| 14″ | 8″ | Arrow |
| 16″ | 10″ | Arrow |
| 18″ | 12″ | Arrow |
| 20″ | 14″ | Arrow |
| 24″ | 18″ | Arrow |
| 30″ | 24″ | Arrow |
Klein 56204, 3/4″ EMT: offset multipliers and shrink
| Angle | Multiplier (printed) | Multiplier (exact) | Shrink per inch (printed) | Shrink per inch (exact) |
|---|---|---|---|---|
| 10° | 6 | 5.759 | 1/16″ | 1/16″ |
| 22-1/2° | 2.6 | 2.613 | 3/16″ | 3/16″ |
| 30° | 2 | 2 | 1/4″ | 1/4″ |
| 45° | 1.4 | 1.414 | 3/8″ | 7/16″ |
| 60° | 1.2 | 1.155 | 1/2″ | 9/16″ |
Printed values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.
Klein 56204, 3/4″ EMT: offsets, distance between bends and shrink
| Depth | 22-1/2° | 30° | 45° |
|---|---|---|---|
| 2″ | 5-3/16″ apart, 3/8″ shrink | 4″ apart, 1/2″ shrink | 2-13/16″ apart, 3/4″ shrink |
| 3″ | 7-13/16″ apart, 9/16″ shrink | 6″ apart, 3/4″ shrink | 4-3/16″ apart, 1-1/8″ shrink |
| 4″ | 10-3/8″ apart, 3/4″ shrink | 8″ apart, 1″ shrink | 5-5/8″ apart, 1-1/2″ shrink |
| 5″ | 13″ apart, 15/16″ shrink | 10″ apart, 1-1/4″ shrink | 7″ apart, 1-7/8″ shrink |
| 6″ | 15-5/8″ apart, 1-1/8″ shrink | 12″ apart, 1-1/2″ shrink | 8-3/8″ apart, 2-1/4″ shrink |
| 8″ | 20-13/16″ apart, 1-1/2″ shrink | 16″ apart, 2″ shrink | 11-3/16″ apart, 3″ shrink |
| 10″ | 26″ apart, 1-7/8″ shrink | 20″ apart, 2-1/2″ shrink | 14″ apart, 3-3/4″ shrink |
Where the maker prints no value for an angle, the exact geometry is shown.
Klein 56205, 1″ EMT
Klein 56205, 1″ EMT: the published values
| Value | Published | Source |
|---|---|---|
| Take-up (deduct) for a 90° stub | 8″ | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
Klein 56205, 1″ EMT: where to mark a 90° stub
| Stub height | Mark from the end | Line up with |
|---|---|---|
| 10″ | 2″ | Arrow |
| 12″ | 4″ | Arrow |
| 14″ | 6″ | Arrow |
| 16″ | 8″ | Arrow |
| 18″ | 10″ | Arrow |
| 20″ | 12″ | Arrow |
| 24″ | 16″ | Arrow |
| 30″ | 22″ | Arrow |
Klein 56205, 1″ EMT: offset multipliers and shrink
| Angle | Multiplier (printed) | Multiplier (exact) | Shrink per inch (printed) | Shrink per inch (exact) |
|---|---|---|---|---|
| 10° | 6 | 5.759 | 1/16″ | 1/16″ |
| 22-1/2° | 2.6 | 2.613 | 3/16″ | 3/16″ |
| 30° | 2 | 2 | 1/4″ | 1/4″ |
| 45° | 1.4 | 1.414 | 3/8″ | 7/16″ |
| 60° | 1.2 | 1.155 | 1/2″ | 9/16″ |
Printed values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.
Klein 56205, 1″ EMT: offsets, distance between bends and shrink
| Depth | 22-1/2° | 30° | 45° |
|---|---|---|---|
| 2″ | 5-3/16″ apart, 3/8″ shrink | 4″ apart, 1/2″ shrink | 2-13/16″ apart, 3/4″ shrink |
| 3″ | 7-13/16″ apart, 9/16″ shrink | 6″ apart, 3/4″ shrink | 4-3/16″ apart, 1-1/8″ shrink |
| 4″ | 10-3/8″ apart, 3/4″ shrink | 8″ apart, 1″ shrink | 5-5/8″ apart, 1-1/2″ shrink |
| 5″ | 13″ apart, 15/16″ shrink | 10″ apart, 1-1/4″ shrink | 7″ apart, 1-7/8″ shrink |
| 6″ | 15-5/8″ apart, 1-1/8″ shrink | 12″ apart, 1-1/2″ shrink | 8-3/8″ apart, 2-1/4″ shrink |
| 8″ | 20-13/16″ apart, 1-1/2″ shrink | 16″ apart, 2″ shrink | 11-3/16″ apart, 3″ shrink |
| 10″ | 26″ apart, 1-7/8″ shrink | 20″ apart, 2-1/2″ shrink | 14″ apart, 3-3/4″ shrink |
Where the maker prints no value for an angle, the exact geometry is shown.
Klein 56211, 1-1/4″ EMT
Klein 56211, 1-1/4″ EMT: the published values
| Value | Published | Source |
|---|---|---|
| Take-up (deduct) for a 90° stub | 11″ | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
Klein 56211, 1-1/4″ EMT: where to mark a 90° stub
| Stub height | Mark from the end | Line up with |
|---|---|---|
| 12″ | 1″ | Arrow |
| 14″ | 3″ | Arrow |
| 16″ | 5″ | Arrow |
| 18″ | 7″ | Arrow |
| 20″ | 9″ | Arrow |
| 24″ | 13″ | Arrow |
| 30″ | 19″ | Arrow |
Klein 56211, 1-1/4″ EMT: offset multipliers and shrink
| Angle | Multiplier (printed) | Multiplier (exact) | Shrink per inch (printed) | Shrink per inch (exact) |
|---|---|---|---|---|
| 10° | 6 | 5.759 | 1/16″ | 1/16″ |
| 22-1/2° | 2.6 | 2.613 | 3/16″ | 3/16″ |
| 30° | 2 | 2 | 1/4″ | 1/4″ |
| 45° | 1.4 | 1.414 | 3/8″ | 7/16″ |
| 60° | 1.2 | 1.155 | 1/2″ | 9/16″ |
Printed values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.
Klein 56211, 1-1/4″ EMT: offsets, distance between bends and shrink
| Depth | 22-1/2° | 30° | 45° |
|---|---|---|---|
| 2″ | 5-3/16″ apart, 3/8″ shrink | 4″ apart, 1/2″ shrink | 2-13/16″ apart, 3/4″ shrink |
| 3″ | 7-13/16″ apart, 9/16″ shrink | 6″ apart, 3/4″ shrink | 4-3/16″ apart, 1-1/8″ shrink |
| 4″ | 10-3/8″ apart, 3/4″ shrink | 8″ apart, 1″ shrink | 5-5/8″ apart, 1-1/2″ shrink |
| 5″ | 13″ apart, 15/16″ shrink | 10″ apart, 1-1/4″ shrink | 7″ apart, 1-7/8″ shrink |
| 6″ | 15-5/8″ apart, 1-1/8″ shrink | 12″ apart, 1-1/2″ shrink | 8-3/8″ apart, 2-1/4″ shrink |
| 8″ | 20-13/16″ apart, 1-1/2″ shrink | 16″ apart, 2″ shrink | 11-3/16″ apart, 3″ shrink |
| 10″ | 26″ apart, 1-7/8″ shrink | 20″ apart, 2-1/2″ shrink | 14″ apart, 3-3/4″ shrink |
Where the maker prints no value for an angle, the exact geometry is shown.
The take-ups grow with the conduit size, so do not judge one of these benders against another by its take-up. The multipliers and shrink per inch are the same on all four charts, because they depend only on the bend angle.
Using the chart: a 90 stub
The stub mark is the stub height less the take-up, measured from the end of the stick that will rise. It lines up with the arrow. Here is a 10 inch stub in 1/2″ EMT on the Klein 56203:
- Stub height
- 10″
| Mark | From the end | Line up with | Bend | Direction |
|---|---|---|---|---|
| 1 | 5″ | Arrow | 90° | First bend |
- Take-up
- 5″
Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2.
The stub rises from the end you measured from, so check which end that is before you mark. The full method is in how to bend a 90 degree stub-up.
Using the chart: an offset
The distance between the two bends of an offset is the depth times the multiplier for the angle. At 30° the Klein multiplier is 2. Here is a 4 inch offset at 30° on the same bender:
- Offset depth
- 4″
- Bend angle
- 30°
| Mark | From the end | Line up with | Bend | Direction |
|---|---|---|---|---|
| 1 | 8″ | Arrow | 30° | First bend |
| 2 | 16″ | Arrow | 30° | Roll the conduit 180° |
- Multiplier
- 2
- Shrink per inch of depth
- 1/4″
- Distance between bends
- 8″
- Shrink
- 1″
Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.
Working away from a fixed end, shrink does not move your marks. It makes the run past the offset shorter by 1/4″ for every inch of depth at 30°, so allow for it when you cut. Other angles have their own multipliers: see 22-1/2 degrees, 30 degrees and 10 degrees.
Steps
For a stub:
- Read the model number on your bender and find its chart above.
- Subtract the take-up for your bender from the stub height. On the Klein 56203 that is 5″.
- Mark the stick that far from the end that will rise.
- Line the mark up with the arrow and pull to 90°. Check it with a level.
For an offset:
- Multiply the depth by the multiplier for your angle. At 30° that is 2 × the depth.
- Make the first mark where the offset is to start. Make the second mark that distance further along the stick.
- Line the first mark up with the arrow and bend to the angle. The degree lines only show how far the bend has gone.
- Take the stick out and roll it exactly half a turn (180°).
- Line the second mark up with the arrow and bend to the same angle.
- Lay the stick on a flat floor and check that both legs lie in one plane.
Mistakes that cost a stick
- Dog legs. Rolling by anything other than half a turn (180°) between the offset bends gives a dog leg.
- Wrong end. Measure every mark from the same end. The stub rises from the end you measured from.
- Shrink toward an obstacle. Working toward an obstacle, the marks must put the full depth at the obstacle. See the shrink chart.
- Over-bending. Stop at the angle you want. Pulling past it and coming back spoils the bend and often the stick.
- Wrong chart. A chart for a different size of Klein bender gives the wrong marks.
Check every mark against your own bender before you cut. Benders differ by model and by wear.
Questions
Is the take-up the same on every Klein bender?
No. The take-up is published per bender and per conduit size. Read the value on the chart for the model and size in your hand.
Which angle should I use for an offset?
Use the angle the job needs. 30° is common, and 10° and 22-1/2° give longer, gentler offsets. Each has its own multiplier on the charts above.
Can I use these marks for saddles?
The charts give the bender's published values. For a saddle, follow the method in three-point saddle or four-point saddle.
How many bends can I put between pull points?
The charts do not cover that. For EMT the limit is in NEC 358.24. Count your bends before you start.
Check against your own bender. The numbers on this page use the values the maker publishes for the bender named; where the maker prints none, they are worked out from the geometry of the bend. Shoes wear, conduit varies and springback differs, so make one test bend and adjust before you bend the run.