Hand bender take-up chart by maker, model and size
Reference · Published November 8, 2026
Take-up, Greenlee 841A, 3/4″ EMT
6″
Take-up changes with the conduit type and size. Find your own bender and size in the table below.
Bender values: Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4.

Your own marks
Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.
Take-up, also called the deduct, is the length a 90° bend uses up. Subtract it from the stub height you want and you have the distance from the end of the stick to your mark. The table below gives the take-up each maker publishes, by model, conduit type and size. After it you will see how to check your own bender against the number.
The take-up chart
| Bender | Conduit | Take-up | Radius | Source |
|---|---|---|---|---|
| Gardner Bender 960 | 1/2″ EMT | 5″ | 3-11/16″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
| Gardner Bender 961 | 3/4″ EMT | 6″ | 4-3/4″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
| Gardner Bender 961 | 1/2″ rigid/IMC | 6″ | 4-3/4″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
| Gardner Bender 962 | 1″ EMT | 8″ | 5-13/16″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
| Gardner Bender 962 | 3/4″ rigid/IMC | 8″ | 5-13/16″ | Gardner Bender Hand Bender How To Guide (960/961/962), page 1 |
| Greenlee 1800 | 1″ rigid/IMC | 11″ | 6-1/16″ | Greenlee 1800 Mechanical Bender instruction manual, page 6 |
| Greenlee 1800 | 3/4″ rigid/IMC | 8-1/2″ | 4-13/16″ | Greenlee 1800 Mechanical Bender instruction manual, page 6 |
| Greenlee 840A | 1/2″ EMT | 5″ | 4-3/16″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 840F | 1/2″ EMT | 5″ | 4-3/16″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 841A | 3/4″ EMT | 6″ | 5-1/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 841A | 1/2″ rigid/IMC | 6″ | 5-1/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 841F | 3/4″ EMT | 6″ | 5-1/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 841F | 1/2″ rigid/IMC | 6″ | 5-1/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 842A | 1″ EMT | 8″ | 6-1/2″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 842A | 3/4″ rigid/IMC | 8″ | 6-1/2″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 842F | 1″ EMT | 8″ | 6-1/2″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 842F | 3/4″ rigid/IMC | 8″ | 6-1/2″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843A | 1-1/4″ EMT | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843A | 1″ rigid/IMC | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843A | 1/2″ rigid/IMC | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843A | 3/4″ rigid/IMC | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843F | 1-1/4″ EMT | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843F | 1″ rigid/IMC | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843F | 1/2″ rigid/IMC | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 843F | 3/4″ rigid/IMC | 11″ | 9-5/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 844A | 1/2″ EMT | 5″ | 4-3/16″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 844A | 3/4″ EMT | 6″ | 5-1/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Greenlee 844A | 1/2″ rigid/IMC | 6″ | 5-1/8″ | Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4 |
| Ideal 74-001 | 1/2″ EMT | not published | — | — |
| Ideal 74-002 | 3/4″ EMT | 6″ | — | Ideal Conduit Bender Guide, page 3 |
| Ideal 74-002 | 1/2″ rigid/IMC | not published | — | — |
| Ideal 74-003 | 1″ EMT | not published | — | — |
| Ideal 74-003 | 3/4″ rigid/IMC | not published | — | — |
| Ideal 74-006 | 1-1/4″ EMT | not published | — | — |
| Ideal 74-006 | 1″ rigid/IMC | not published | — | — |
| Ideal 74-031 | 1/2″ EMT | not published | — | — |
| Ideal 74-032 | 3/4″ EMT | 6″ | — | Ideal Conduit Bender Guide, page 3 |
| Ideal 74-032 | 1/2″ rigid/IMC | not published | — | — |
| Ideal 74-033 | 1″ EMT | not published | — | — |
| Ideal 74-033 | 3/4″ rigid/IMC | not published | — | — |
| Ideal 74-036 | 1-1/4″ EMT | not published | — | — |
| Ideal 74-036 | 1″ rigid/IMC | not published | — | — |
| Klein 56203 | 1/2″ EMT | 5″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56204 | 3/4″ EMT | 6″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56204 | 1/2″ rigid/IMC | 6″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56205 | 1″ EMT | 8″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56205 | 3/4″ rigid/IMC | 8″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56206 | 1/2″ EMT | 5″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56207 | 3/4″ EMT | 6″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56207 | 1/2″ rigid/IMC | 6″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56211 | 1-1/4″ EMT | 11″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
| Klein 56211 | 1″ rigid/IMC | 11″ | — | Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2 |
Find your bender's maker and model, then the row for the conduit type and size you are bending. One bender head often bends more than one conduit, and each has its own row. Take-up changes with size and conduit type, so compare benders only within the same type and size: a 1/2 inch EMT bender and a 3/4 inch EMT bender differ for that reason alone. Where a row says "not published", the maker gives no take-up for that bender, and you measure your own with the steps below.
Using take-up on a stub
The mark is the stub height less the take-up, measured from the end of the stick that will rise. It lines up with the arrow on a hand bender. Here is a 14 inch stub on a Greenlee 841A in 3/4″ EMT, which has a take-up of 6″:
- Stub height
- 14″
| Mark | From the end | Line up with | Bend | Direction |
|---|---|---|---|---|
| 1 | 8″ | Arrow | 90° | First bend |
- Take-up
- 6″
- Gain
- 2-3/16″
Bender values: Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4.
Calculate this bend in Bendbook. Pick your bender, type your measurements, and every mark is drawn on the stick for you.
The stub height runs from the end of the stick to the back of the 90, not along the run. Measure the finished stub the same way. For the full stub procedure, see how to bend a 90 degree stub-up.
Steps: check your own bender's take-up
Do this once per bender and conduit size, on a short piece of the same conduit you will bend.
- Pick a stub height. Subtract the take-up from the table for your bender and size.
- Mark the stick that far from the end that will rise. Draw the mark all the way around.
- Seat the stick in the bender and line the mark up with the arrow.
- Bend to 90°. Stop when the stub is square to the straight run, checked with a level, not when a degree line says so.
- Measure the finished stub from that same end to the back of the 90.
- Subtract the distance to your mark from the stub you measured. That is your bender's take-up. If it matches the table, trust the table.
- If it does not match, bend a second test piece. If the two agree, use your own figure and write it on the bender. If they do not, check the bend for over- or under-bending and the bender for wear.
A worn shoe, a bent handle or a head for the wrong conduit size will shift a stub. Check your own bender before you cut a run.
Mistakes that cost a stick
- Using another size's take-up. A take-up from a different conduit size or type puts the mark in the wrong place.
- Reading the wrong row. One head can have rows for EMT and for rigid. Read the row for the conduit in your hand.
- Measuring from the wrong end. The mark is measured from the end that becomes the top of the stub.
- Bending past 90°. The take-up only holds at 90°. Stop at 90° and check with a level.
- Applying take-up to an offset. Offsets use a multiplier and shrink, not take-up. See the offset multiplier for 30 degrees.
Questions
Is take-up the same as the deduct?
Yes. Take-up and deduct are two names for the same number: the length a 90° bend uses up, which you subtract from the stub height to find your mark.
Why does take-up change with the conduit size?
A bigger conduit needs a bigger shoe with a bigger bend radius, and the bend uses up more of the stick. That is why the chart lists the size on every row.
Can I use the take-up from a different conduit size on my bender?
No. Take-up changes with conduit size and type. Use the row for the conduit type and size you are bending.
Does take-up matter for saddles and offsets?
Not directly. Saddles and offsets use a multiplier and the spacing between marks. See how to bend a three-point saddle and how to bend a four-point saddle. Take-up is for 90s and stubs. More bends are in the guides index.
Check against your own bender. The numbers on this page use the values the maker publishes for the bender named; where the maker prints none, they are worked out from the geometry of the bend. Shoes wear, conduit varies and springback differs, so make one test bend and adjust before you bend the run.