How to bend an offset on 1 inch EMT
How to bend · Published November 8, 2026
Distance between bends
12″
A 6 inch offset at 30° on a Greenlee 842A, 1 inch EMT. Both marks go on the arrow.
Bender values: Greenlee Use Guide, Site-Rite 840–844 hand benders, page 9; Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4.

Your own marks
Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.
To bend an offset on 1 inch EMT, multiply the depth by the multiplier for your angle to get the distance between two marks. Bend at the first mark with it on the arrow, roll the stick exactly 180°, and bend the second mark to the same angle. The method is the same as on smaller EMT. The difference is room: 1 inch EMT bends on a larger radius, so leave more straight stick around the offset.
Why 1 inch EMT needs more room
A hand bender for 1 inch EMT has a bigger shoe than the smaller sizes. For a Greenlee 842A on 1 inch EMT, the published centerline radius is 6-1/2″. Each bend curves over a longer stretch of stick, so:
- Leave enough straight stick on both sides of the offset to seat it in the bender.
- Work the marks from the multiplier and shrink published for your bender, not from habit on smaller conduit.
Take-up is for stubs and 90s. It does not place the marks of an offset. If you also bend stubs in this size, see the 1 inch EMT take-up chart.
Worked example: a 6 inch offset at 30°
A 6 inch offset on a Greenlee 842A, bent at 30° and measured from the end of the stick. Greenlee prints a 30° multiplier of 2 and a shrink of 1/4″ per inch of depth. The 30 degree multiplier guide covers that angle in detail.
- Offset depth
- 6″
- Bend angle
- 30°
| Mark | From the end | Line up with | Bend | Direction |
|---|---|---|---|---|
| 1 | 12″ | Arrow | 30° | First bend |
| 2 | 24″ | Arrow | 30° | Roll the conduit 180° |
- Multiplier
- 2
- Shrink per inch of depth
- 1/4″
- Distance between bends
- 12″
- Shrink
- 1-1/2″
- Gain
- 3/16″
Bender values: Greenlee Use Guide, Site-Rite 840–844 hand benders, page 9; Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4.
Calculate this bend in Bendbook. Pick your bender, type your measurements, and every mark is drawn on the stick for you.
Both marks go on the arrow, and the one nearest the end is bent first.
Steps
- Check that the bender is for 1 inch EMT. The model and size are on the head.
- Measure the offset depth.
- Multiply the depth by the multiplier for your angle, 2 at 30°. That is the distance between the marks.
- Make the first mark where the offset should start, measured from the end you are working from.
- Make the second mark the distance between bends past the first, away from the end.
- Before the first bend, check which way the offset has to kick.
- Line the first mark up with the arrow. Keep your foot heavy on the heel and bend to 30°.
- Take the stick out and roll it exactly half a turn, 180°. Do not guess it by eye.
- Slide the stick to the second mark and line it up with the arrow.
- Bend to 30° again.
- Lay the stick on a flat floor. The two straight legs should lie flat and run parallel, with no twist.
Working toward an obstacle
When you work away from a fixed end, shrink does not move the marks. It makes the run past the offset shorter, so it matters when you cut the stick.
When you work toward an obstacle or a box you are bending into, the marks must put the full depth at that point. Here is the same 6 inch, 30° offset with the obstacle 48 inches from the end, measured to the far bend.
- Offset depth
- 6″
- Bend angle
- 30°
- Distance to the obstacle
- 48″
| Mark | From the end | Line up with | Bend | Direction |
|---|---|---|---|---|
| 1 | 49-1/2″ | Arrow | 30° | First bend |
| 2 | 37-1/2″ | Arrow | 30° | Roll the conduit 180° |
- Multiplier
- 2
- Shrink per inch of depth
- 1/4″
- Distance between bends
- 12″
- Shrink
- 1-1/2″
- Gain
- 3/16″
Bender values: Greenlee Use Guide, Site-Rite 840–844 hand benders, page 9; Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4.
The far mark is the obstacle distance plus the shrink, 1/4″ for every inch of depth. That puts the full depth at the obstacle. The near mark is the distance between bends back toward the end. Bend the far mark first, roll 180°, then bend the near mark. The shrink is already in the far mark, so do not add it again. The shrink chart lists shrink for each angle.
Before you pull, hold the stick up to the obstacle and check which way the offset has to kick to clear it.
Mistakes that cost a stick
- A dog leg. The roll between bends was not exactly 180°. The two legs then sit out of line.
- Measuring from the wrong end. Take both marks from the same end.
- Forgetting shrink when working toward an obstacle. The depth comes out right, but the offset lands short of the obstacle by the shrink.
- The wrong head mark. For an offset, the mark goes on the arrow. The degree lines only show how far the bend has gone.
- Two different angles. A second bend to a different angle gives an offset whose legs are not parallel. Check the first bend before you roll.
- Using another bender's figures. Take the multiplier and shrink for your own model and size.
Questions
Can I use the same marks on a different 1 inch bender?
Check first. Each maker prints its own figures. Use the ones for your own bender, and check the offset against it. The Greenlee chart and Klein chart list the published values by model.
Which angle should I use on 1 inch EMT?
Use the angle that fits the space. A shallow angle such as 22-1/2° or 10° gives a longer, gentler offset, and 45° or 60° gives a shorter one. A shallow angle needs more length between the bends, so check the room first. See the 22-1/2 degree multiplier and the 10 degree multiplier.
What if the conduit has to clear a pipe in the middle of a run?
That is a saddle, not an offset. Start with the three-point saddle or the four-point saddle.
Does the NEC limit how many bends I can make?
Check 358.24 for EMT, in Article 358, for the bends allowed between pull points. Confirm the rule in the edition your jurisdiction has adopted, 2023 or 2026.
Check against your own bender. The numbers on this page use the values the maker publishes for the bender named; where the maker prints none, they are worked out from the geometry of the bend. Shoes wear, conduit varies and springback differs, so make one test bend and adjust before you bend the run.