45 degree rolling offset: true offset and marks

How to bend · Published November 8, 2026

True offset, 8″ rise and 6″ roll

10″

Bend this as a plain 45° offset on a Klein 56204, 3/4 inch EMT, then roll it into place.

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.

Rolling offset on a Klein 56204, 3/4″ EMT: mark 1 at 14″, mark 2 at 28″28″14″END12END12
Rolling offset on a Klein 56204, 3/4″ EMT: mark 1 at 14″, mark 2 at 28″. Numbered in bending order.
Bendbook’s bender list, with a Klein 3/4″ EMT bender picked

Your own marks

Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.

A rolling offset moves the conduit up or down and sideways in one move. Find the true offset from the rise and the roll, then mark and bend it like a plain offset at 45°. The only difference is that the finished offset leans over, so it moves the conduit on the diagonal.

How the true offset works

The rise and the roll are the two sides of a right triangle. The true offset is the diagonal across it. To find it, square the rise and square the roll, add them, and take the square root.

The offset you bend is the size of that diagonal, not the rise. Once it is bent, the stick is turned in the run so the offset leans from straight up toward the roll side. The roll angle is how far it leans.

The worked example

Take a Klein 56204 bender and 3/4 inch EMT. The conduit has to rise 8 inches and roll 6 inches. The true offset is 10″, and the offset leans 36.9° from straight up.

Worked exampleRolling offset on a Klein 56204, 3/4″ EMT, numbers as printed in the maker’s guide
Rise
8″
Roll
6″
Bend angle
45°
MarkFrom the endLine up withBendDirection
114″Arrow45°First bend
228″Arrow45°Roll the conduit 180°
Multiplier
1.4
Shrink per inch of depth
3/8″
Distance between bends
14″
Shrink
3-3/4″
True offset
10″
Roll angle
36.9°

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.

Calculate this bend in Bendbook. Pick your bender, type your measurements, and every mark is drawn on the stick for you.

The distance between the bends comes from the true offset, not the rise. Both marks go under the arrow, and both bends are 45°.

Working away from a fixed end, shrink does not move your marks. It only makes the run past the offset shorter, so allow for it when you cut the stick. At 45° on this bender the shrink is 3/8″ per inch of true offset. For other angles, see conduit shrink per inch of offset.

Steps

  1. Measure the rise and the roll at the job. Write both down.
  2. Work out the true offset: square the rise, square the roll, add them and take the square root. For an 8 inch rise and a 6 inch roll it is 10″.
  3. Work out the distance between bends: the true offset × the multiplier. At 45° on a Klein 56204 it is 1.4.
  4. Measure from the end of the stick to where the offset has to start. Make the first mark there.
  5. Make the second mark the distance between bends further from the end.
  6. Line the first mark up with the arrow and bend 45°.
  7. Roll the stick exactly half a turn (180°). Any other roll gives a dog leg.
  8. Line the second mark up with the arrow and bend 45°.
  9. Lay the stick on the floor. Both bends should sit flat in one plane, like any offset.
  10. Set the stick in the run and turn it until the offset leans toward the roll side. The far end should land up by the rise and over by the roll.

Check the multiplier and shrink against your own bender. They differ between makers and between sizes.

Mistakes that cost a stick

  • Using the rise alone. The rise by itself gives a plain offset that comes up short on the diagonal. Bend the true offset.
  • Rolling the wrong amount between bends. Half a turn, no more and no less. Anything else puts a twist in the offset.
  • Trying to bend the lean into the stick. Bend a flat offset first, then turn the whole stick in the run.
  • Measuring from the wrong end. Pick one end and mark everything from it.
  • Forgetting shrink when you cut. The run past the offset comes up short by the shrink.
  • Over-bending. Stop at 45°. Pulling past it makes the offset deeper than the true offset.

Questions

Can I bend a rolling offset at an angle other than 45°?

Yes. The true offset is the same. Only the multiplier, and so the distance between the bends, changes. Shallow angles need more room, as shown in the 22-1/2 degree multiplier. For a 30° bend, see the 30 degree multiplier.

What if the roll is bigger than the rise?

The same steps hold. The true offset is still the square root of the rise squared plus the roll squared. The offset just leans further from straight up. Work it out again for the new numbers. Don't reuse the marks from another job.

Do I use the same bender for every size of conduit?

No. Each bender is made for a size and type of conduit. The Klein bender chart and the Greenlee bender chart list the published values. For take-up across benders of the same size, see the hand bender take-up chart.

How is this different from a plain offset?

A plain offset moves the conduit in one direction. A rolling offset moves it in two at once. You bend it the same way, but the offset you bend is the diagonal, and the finished stick leans over in the run.

Check against your own bender. The numbers on this page use the values the maker publishes for the bender named; where the maker prints none, they are worked out from the geometry of the bend. Shoes wear, conduit varies and springback differs, so make one test bend and adjust before you bend the run.