1-1/4 inch EMT take-up and bending chart

Bender charts · Published November 8, 2026

Take-up, 1-1/4″ EMT

11″

Subtract it from the stub height you want. The result is your mark, measured from the end of the stick.

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2.

90° stub-up on a Klein 56211, 1-1/4″ EMT: mark 1 at 1″1″END1END1
90° stub-up on a Klein 56211, 1-1/4″ EMT: mark 1 at 1″. Numbered in bending order.
Bendbook’s bender list, with a Klein 3/4″ EMT bender picked

Your own marks

Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.

The take-up for a 1-1/4 inch EMT hand bender is 11″. Take-up is the length the bender uses up in a 90°. To bend a stub, subtract the take-up from the stub height you want, mark the stick that far from the end, line the mark up with the arrow and pull to 90°.

Take-up of 1-1/4 inch EMT benders

BenderTake-upRadiusSource
Greenlee 843A11″9-5/8″Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4
Greenlee 843F11″9-5/8″Greenlee Use Guide, Site-Rite 840–844 hand benders, page 4
Ideal 74-006not published——
Ideal 74-036not published——
Klein 5621111″—Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2

Every 1-1/4 inch EMT bender in this table that publishes a take-up prints the same one, so the mark for a given stub is the same on any of them. The maker publishes no take-up for the Ideal 74-006 and 74-036. If you bend with one of those, use the take-up in the instructions that came with it, or measure your own from a test stub, as described under Questions below.

These numbers are for 1-1/4 inch EMT only. Take-up grows with conduit size, so a figure from a smaller size puts the mark in the wrong place. For the smaller sizes, see 1 inch EMT take-up and 3/4 inch EMT take-up.

Where to mark common stubs

The mark is the stub height less the take-up, measured from the end of the stick that will rise.

Stub heightMark from the endLine up with
12″1″Arrow
14″3″Arrow
16″5″Arrow
18″7″Arrow
20″9″Arrow
24″13″Arrow
30″19″Arrow

Take-up 11″: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2.

Worked example: a 12 inch stub

Worked example90° stub-up on a Klein 56211, 1-1/4″ EMT, numbers as printed in the maker’s guide
Stub height
12″
MarkFrom the endLine up withBendDirection
11″Arrow90°First bend
Take-up
11″

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2.

Calculate this bend in Bendbook. Pick your bender, type your measurements, and every mark is drawn on the stick for you.

The stub height runs from the end of the stick to the back of the bend, the outside of the 90. That is what the take-up assumes, so measure the finished stub the same way when you check it.

Steps

  1. Measure the stub height you need. Decide which end of the stick will rise.
  2. Subtract the take-up, 11″, from the stub height. Mark the stick that far from the end that will rise.
  3. Draw the mark all the way around the stick, so you can see it with the stick in the shoe.
  4. Seat the stick in the bender and line the mark up with the arrow.
  5. Before you pull, check that the stub will come up from the end you measured from. If it would come up from the other end, take the stick out and turn it around.
  6. Keep your foot heavy on the heel and the stick flat on the floor. Pull the handle in one steady motion until the stub reaches 90°.
  7. Check the stub with a level, then measure from the end of the stick to the back of the bend.

Mistakes that cost a stick

  • Using another size's take-up. Match the number to the bender and the conduit size in your hand.
  • Measuring from the wrong end. The mark is measured from the end the stub rises from, not from the far end of the stick.
  • Lining the mark up with the wrong head mark. For a stub, the mark goes on the arrow. The degree lines only show how far the bend has gone.
  • Over-bending. Going past 90° and pulling back is hard to get right on 1-1/4 inch EMT. Stop at 90° and check it.
  • Skipping the check. Your bender may not match the printed numbers exactly. Bend one scrap piece and measure it before you cut the real run.

For what the arrow is for, see the arrow on a conduit bender.

Questions

Is the take-up the same on every 1-1/4 inch EMT bender?

For every bender in the table that publishes one, yes. Find your model in the table and make sure you are reading the 1-1/4 inch EMT line.

Does the stub mark change with the stub height?

Yes. The mark is always the stub height less the take-up, so a taller stub puts the mark further from the end. The stub table above shows the common heights.

What if my bender has no published take-up?

Bend one test stub. Put a mark a known distance from the end, line it up with the arrow and bend a 90. Measure the stub from the end to the back of the bend. The stub height less the distance to your mark is your take-up.

Where can I see all the benders side by side?

Go to the hand bender take-up chart. For one maker's full chart, see the Klein bender chart or the Greenlee bender chart. The 90 degree stub-up guide covers the bend in more detail.

Check against your own bender. The numbers on this page use the values the maker publishes for the bender named; where the maker prints none, they are worked out from the geometry of the bend. Shoes wear, conduit varies and springback differs, so make one test bend and adjust before you bend the run.