Conduit bender markings: the arrow, star and rim notch

How to bend · Published November 8, 2026

Mark for a 10″ stub

5″

On a Klein 56203, 1/2 inch EMT: measure it from the end and put it under the arrow.

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2.

90° stub-up on a Klein 56203, 1/2″ EMT: mark 1 at 5″5″END1END1
90° stub-up on a Klein 56203, 1/2″ EMT: mark 1 at 5″. Numbered in bending order.
Bendbook’s bender list, with a Klein 3/4″ EMT bender picked

Your own marks

Bendbook draws every mark for the bender in your hand, numbered in bending order. Offline.

A hand bender head carries a few marks, and each one has a single job. The arrow is for stubs, offsets and kicks. The star is for the second 90 of a back-to-back. The rim notch is for the center bend of a 3-point saddle. The degree lines show how far the bend has gone and are not for lining up marks.

Head layouts differ between makers and models, so find these marks on your own bender before you rely on this page.

The arrow

The arrow is the mark you will use most. For a stub-up, subtract the take-up from the stub height, mark the stick that far from the end, and put the mark under the arrow. On a Klein 56203 with 1/2 inch EMT the take-up is 5″.

Worked example90° stub-up on a Klein 56203, 1/2″ EMT, numbers as printed in the maker’s guide
Stub height
10″
MarkFrom the endLine up withBendDirection
15″Arrow90°First bend
Take-up
5″

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2.

Calculate this bend in Bendbook. Pick your bender, type your measurements, and every mark is drawn on the stick for you.

The stub rises from the end you measured from. See how to bend a 90 degree stub-up for the full method.

The arrow on an offset

An offset uses the arrow twice, once for each bend. The distance between the two marks is the offset depth × the multiplier for your angle. At 30° on a Klein 56203 the multiplier is 2. Here is a 4 inch offset at 30° on that bender:

Worked exampleOffset on a Klein 56203, 1/2″ EMT, numbers as printed in the maker’s guide
Offset depth
4″
Bend angle
30°
MarkFrom the endLine up withBendDirection
18″Arrow30°First bend
216″Arrow30°Roll the conduit 180°
Multiplier
2
Shrink per inch of depth
1/4″
Distance between bends
8″
Shrink
1″

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 6.

Offset on a Klein 56203, 1/2″ EMT: mark 1 at 8″, mark 2 at 16″16″8″END12END12
Offset on a Klein 56203, 1/2″ EMT: mark 1 at 8″, mark 2 at 16″. Numbered in bending order.

Both marks go under the arrow. Between the two bends, roll the stick exactly half a turn (180°). Any other roll gives a dog leg. Working away from a fixed end, shrink does not move these marks. It only shortens the run past the offset, which matters when you cut the stick. For the multiplier at other angles, see the 30 degree offset multiplier and the 22-1/2 degree offset multiplier.

The star

The star is for the second 90 of a back-to-back. Bend the first 90 as a normal stub, with its mark under the arrow. Then measure from the back of the first 90 to where the back of the second 90 must land, and mark the stick there. That mark goes to the star, not the arrow, and you bend it the same way as the first, so the two stubs stand up side by side.

Worked exampleBack-to-back 90 on a Klein 56203, 1/2″ EMT, numbers as printed in the maker’s guide
First stub height
12″
Back of the first 90 to the back of the second
30″
MarkFrom the endLine up withBendDirection
17″Arrow90°First bend
242″Star90°Same way as bend 1
Take-up
5″

Bender values: Klein Tools Conduit Bender Guide (56203–56207, 56211), page 2.

Do not use the star for a single stub. It does not replace the arrow there.

The rim notch

The rim notch is for saddles. On a 3-point saddle the center bend is made first, with the center mark lined up with the rim notch. The two outer marks go to the arrow.

Worked exampleThree-point saddle on a Klein 56203, 1/2″ EMT, numbers as printed in the maker’s guide
Obstacle height
3″
Center bend angle
45°
Distance to the center of the obstacle
20″
MarkFrom the endLine up withBendDirection
120-9/16″Rim notch45°First bend
213-1/16″Arrow22-1/2°Roll the conduit 180°
328-1/16″Arrow22-1/2°Same way as bend 2
Multiplier for the outer marks
2.5
Shrink per inch of saddle height
3/16″
Shrink, added to the center distance
9/16″
Center mark to each outer mark
7-1/2″

The outer bends are each half the center angle, the other way. Roll the stick 180° after the center bend. For the last outer bend, take the stick out and turn it end for end, so the center bend sits on the same side of the head as before, still pointing the same way. The full method is in how to bend a three-point saddle and the three-point saddle formula. A 4-point saddle uses the arrow for all four bends.

The degree lines

The degree lines show how far the bend has gone: 10°, 22-1/2°, 30°, 45°, 60° and 90°. Use them to stop at the angle you want. Never line a mark up with a degree line. The mark goes to the arrow, the star or the rim notch.

Steps

  1. Find the arrow, the star, the rim notch and the degree lines on your bender head.
  2. Work out the marks for your bend, all measured from the same end of the stick, and mark them.
  3. For a stub, a kick or either bend of an offset, put the mark under the arrow.
  4. For the second 90 of a back-to-back, put the mark at the star.
  5. For the center bend of a 3-point saddle, put the center mark at the rim notch. The outer marks go to the arrow.
  6. Bend until the stick reaches the angle you want on the degree lines.
  7. Before the second bend of an offset, roll the stick exactly half a turn (180°).
  8. Check the finished bend against your measurements before you cut or install it.

Mistakes that cost a stick

  • Lining a mark up with a degree line. The degree lines only show progress. The mark goes to the arrow, star or rim notch.
  • Using the arrow for the second 90 of a back-to-back. That bend uses the star.
  • Rolling the wrong amount on an offset. Roll half a turn (180°), or you get a dog leg.
  • Measuring from the wrong end. The stub rises from the end you measured from. Check this before the first bend.
  • Forgetting shrink when working toward an obstacle. The marks have to put the full depth at the obstacle, not before it. See the shrink chart.
  • Over-bending. Stop at the angle. Bending past it does not come back cleanly.

Head layouts differ between benders. Check each mark against your own bender before you cut.

Questions

Is the arrow always the mark to use?

No. The arrow is for stubs, offsets and kicks. The second 90 of a back-to-back uses the star, and a 3-point saddle's center bend uses the rim notch.

What are the degree lines for?

They show how far the bend has gone, so you know when to stop. They are not marks to line up with.

Do I use the same head mark for both bends of an offset?

Yes. Both marks go to the arrow, with the stick rolled half a turn (180°) between the bends. A kick is a single bend at the arrow. See how to bend a kick in conduit.

Do these marks work on any bender?

The idea is the same, but the layout changes by maker and model. Check the head of your own bender, and use its chart. See the Klein chart and the Greenlee chart.

Check against your own bender. The numbers on this page use the values the maker publishes for the bender named; where the maker prints none, they are worked out from the geometry of the bend. Shoes wear, conduit varies and springback differs, so make one test bend and adjust before you bend the run.